This document provides information on various construction materials used in building, including their classification and properties. It discusses stones, classified as igneous, sedimentary and metamorphic based on their geological formation. Bricks and tiles are described as clay products manufactured through processes of preparation, moulding, drying and burning. The characteristics of good building stones and various stone varieties are also summarized.
The document discusses various materials used in civil engineering construction projects such as bricks, stones, aggregates, cement, and concrete. It provides details on the manufacturing process and properties of bricks and describes the different types of bricks used. It also discusses the characteristics, classification, and uses of stones as a building material. The qualities, types, and uses of aggregates and cement are outlined. Concrete is introduced as a composite material made by mixing aggregates, sand, cement, and water.
Stones have been used in construction for thousands of years in buildings all over the world. They are classified geologically based on their mode of formation as igneous, sedimentary, or metamorphic rocks. Igneous rocks form from cooling magma, sedimentary rocks form from compressed sediments, and metamorphic rocks form from changes to existing rocks. Stones are also classified chemically based on their dominant composition of silica, calcareous, or argillaceous minerals. Structurally, stones can occur as massive unstratified rocks, stratified layered rocks, or foliated banded rocks. Many historical structures were constructed of stone and it remains an important building material.
The document discusses different types of mortar used in construction. It defines mortar as a mixture of a binding material, fine aggregate, and water. Common binding materials include cement and lime. Mortars are classified by their binding material, such as cement mortar, lime mortar, and mud mortar. Specialty mortars include fire resistant mortar, lightweight mortar, and chemical resistant mortar which are formulated for specific applications. The document outlines the proper mixing and application of different mortars.
Concrete Construction: Batching of mixes; casting process, compaction and curing;
requirement of mix design and casting of test cubes – removing cubes from moulds and
curing for strength tests; bar-bending equipments and preparation of reinforcement for
R C C works
This document discusses common building construction materials including stone, brick, lime, cement, metal, timber, sand, aggregates, and mortar. For each material, requirements and types are outlined. Stone, brick, lime and cement are described as traditional materials while metal, timber, sand and aggregates are described as both natural and artificial options. The document also briefly introduces concrete, describing its ingredients, types, requirements and common uses in construction.
This document describes the properties of bricks, including their physical, mechanical, and thermal characteristics. It discusses the shape, size, color, density, compressive strength, insulation properties, durability, and frost resistance of standard bricks. It also outlines various tests conducted on bricks, such as those measuring compressive strength and water absorption. Additionally, it defines the qualities of good bricks and provides a classification system for bricks based on their characteristics and intended uses. Special types of bricks are also outlined, including those with modified shapes, perforations, and alternative compositions like sand lime bricks and refractory fire bricks.
1. Plastering is done for protection, smooth surfaces, decoration, and to conceal defects. Requirements include adhesion, affordability, hardness, and workability.
2. Common plaster types include sand faced, rough cast, pebbled dash, and smooth cast.
3. Defects can include blistering, cracking, efflorescence, flaking, peeling, and popping. Cracking is caused by structural issues or drying movements.
The document discusses various materials used in civil engineering construction projects such as bricks, stones, aggregates, cement, and concrete. It provides details on the manufacturing process and properties of bricks and describes the different types of bricks used. It also discusses the characteristics, classification, and uses of stones as a building material. The qualities, types, and uses of aggregates and cement are outlined. Concrete is introduced as a composite material made by mixing aggregates, sand, cement, and water.
Stones have been used in construction for thousands of years in buildings all over the world. They are classified geologically based on their mode of formation as igneous, sedimentary, or metamorphic rocks. Igneous rocks form from cooling magma, sedimentary rocks form from compressed sediments, and metamorphic rocks form from changes to existing rocks. Stones are also classified chemically based on their dominant composition of silica, calcareous, or argillaceous minerals. Structurally, stones can occur as massive unstratified rocks, stratified layered rocks, or foliated banded rocks. Many historical structures were constructed of stone and it remains an important building material.
The document discusses different types of mortar used in construction. It defines mortar as a mixture of a binding material, fine aggregate, and water. Common binding materials include cement and lime. Mortars are classified by their binding material, such as cement mortar, lime mortar, and mud mortar. Specialty mortars include fire resistant mortar, lightweight mortar, and chemical resistant mortar which are formulated for specific applications. The document outlines the proper mixing and application of different mortars.
Concrete Construction: Batching of mixes; casting process, compaction and curing;
requirement of mix design and casting of test cubes – removing cubes from moulds and
curing for strength tests; bar-bending equipments and preparation of reinforcement for
R C C works
This document discusses common building construction materials including stone, brick, lime, cement, metal, timber, sand, aggregates, and mortar. For each material, requirements and types are outlined. Stone, brick, lime and cement are described as traditional materials while metal, timber, sand and aggregates are described as both natural and artificial options. The document also briefly introduces concrete, describing its ingredients, types, requirements and common uses in construction.
This document describes the properties of bricks, including their physical, mechanical, and thermal characteristics. It discusses the shape, size, color, density, compressive strength, insulation properties, durability, and frost resistance of standard bricks. It also outlines various tests conducted on bricks, such as those measuring compressive strength and water absorption. Additionally, it defines the qualities of good bricks and provides a classification system for bricks based on their characteristics and intended uses. Special types of bricks are also outlined, including those with modified shapes, perforations, and alternative compositions like sand lime bricks and refractory fire bricks.
1. Plastering is done for protection, smooth surfaces, decoration, and to conceal defects. Requirements include adhesion, affordability, hardness, and workability.
2. Common plaster types include sand faced, rough cast, pebbled dash, and smooth cast.
3. Defects can include blistering, cracking, efflorescence, flaking, peeling, and popping. Cracking is caused by structural issues or drying movements.
Concrete is a widely used construction material consisting of cement, water, and aggregates. The strength of concrete is specified using its 28-day cube strength in N/sq.mm. Formwork is used to mold wet concrete into desired shapes and allow it to cure. Formwork design involves choosing traditional or systematic approaches using wood or steel components like props, beams, sheathing to form columns, walls, and beams until the concrete gains sufficient strength. Proper formwork is important for quality concrete finish and structural integrity.
Cement tests can be divided into field tests and laboratory tests. Laboratory tests include fineness test, standard consistency test, setting time test, compressive strength test, soundness test, and tensile strength test. The fineness test measures the mean size of cement grains and finer cement results in earlier strength development but more shrinkage and cracking. The standard consistency test determines the percentage of water required to form a cement paste using a Vicat apparatus. The setting time test uses the Vicat apparatus to detect when cement paste reaches its initial and final set. The compressive strength test forms cement mortar cubes which are tested at 3 and 7 days to determine strength. The soundness test uses a Le-Chatelier apparatus to
This document defines bricks and their constituents and manufacturing process. It provides the following key details:
- Bricks are clay constructions of uniform size and shape, traditionally 23cm x 11.4cm x 7.6cm or modular 19cm x 9cm x 9cm.
- Good bricks contain 50-60% silica, 20-30% alumina, up to 5% lime, and 5-6% iron oxide.
- Bricks are manufactured through processes of preparation, molding, drying for 7-14 days, and burning at 750-1000°C using clamp or kiln methods.
- Various bonds including English, Flemish, stretcher and header are used in brickwork construction
Concrete is the most widely used building material due to its low cost, fireproof and weatherproof properties, and ability to be molded into any shape. It is a composite material made of cement, water, and aggregates. Reinforced concrete is concrete strengthened with steel bars. Brick is made from fired clay and is cheap and strong in compression. Cast iron is strong but weaker than steel. Steel is one of the strongest materials and is used widely in construction. Aluminum is lightweight but expensive. Wood is cheap and moderately strong but can rot and burn easily. Plastic is flexible, lightweight, and strong in compression and tension but is expensive.
This document provides information about building stones. It begins by defining stone and rock. It then discusses different ways stones can be classified, including by geology, physical properties, chemistry, and hardness. Specific rock types that make good building stones are mentioned, such as granite, limestone, marble, and slate. The document outlines various tests used to evaluate stones, including acid resistance, water absorption, impact resistance, and crushing strength. Finally, it briefly discusses the processes of quarrying, dressing, and seasoning stones for construction.
Curing concrete is important to allow the cement hydration process to continue and develop strength over time. Proper curing ensures concrete reaches its designed strength and durability by controlling moisture loss. Common curing methods include water curing through ponding, sprinkling or wet coverings; membrane curing using plastic sheeting or curing compounds; and steam curing to accelerate strength gain. Curing should continue for at least 7 days for normal concrete and 14 days if blended cements are used. Inadequate curing can lead to reduced strength, increased permeability and poor durability.
This document provides an overview of various common building materials used in civil engineering projects. It discusses the composition, properties, uses and testing procedures for water, concrete, cement, aggregates, paints/coatings, bricks, stones, metals/steel, timber and glass. For each material, key details are given around its history, ingredients, strengths and applications in construction. Standards and quality measures are also outlined. The document serves as a basic introduction to the principal materials that civil engineers work with.
Mortar is a workable paste used to bind construction blocks together and fill gaps. It is typically made of sand, a binder like cement or lime, and water. Mortar hardens after setting to form a rigid structure. Different types of mortar are used depending on the binder, intended use, and required properties. Cement mortar provides high strength and is used for load-bearing walls. Lime mortar is used above ground, while mud mortar is a cheaper option for ordinary buildings. Special mortars include fire-resistant, lightweight, and sound absorbing varieties.
Building materials elements of civil engineeringPriyank Bhimani
The document discusses various construction materials used in civil engineering projects. It describes properties and composition of common materials like stone, bricks, lime, cement, sand and aggregate. It provides details on manufacturing processes, types and qualities required for stones, bricks and lime to be suitable for construction purposes. The mechanical and physical properties of construction materials are also outlined.
Properties of fresh and Hardened ConcreteVijay RAWAT
The document discusses various properties of fresh and hardened concrete. It describes workability, consistency, segregation, bleeding, mixing, placing, consolidating, and curing of fresh concrete. It also discusses compressive strength, tensile strength, modulus of elasticity, permeability, and durability of hardened concrete. The key properties of fresh concrete include workability, consistency, segregation, bleeding, setting time, and uniformity. Compressive strength is identified as the most important property of hardened concrete.
This document discusses the classification and properties of aggregates used in concrete. It describes three main classifications of aggregates: 1) based on unit weight as normal, heavyweight, or lightweight, 2) based on size as fine or coarse aggregate, and 3) based on shape as rounded, irregular, angular, or flaky. It then discusses various physical and engineering properties of aggregates including size, shape, strength, surface texture, specific gravity, bulk density, water absorption, and soundness. The purpose is to provide information on aggregates for use in concrete mixtures in civil engineering applications.
This document discusses various factors that affect the choice of building construction materials. It describes key properties that materials must have for different applications, including strength, resistance to water, acids, fire, weathering, frost, and durability. The document emphasizes that understanding materials' properties allows choosing the optimal material for a given service condition or climate. Standardization is also important to ensure materials meet minimum quality levels and drive industry improvement.
This document provides information on concrete mix design, including objectives, basic considerations, and the IS (Indian Standards) method for mix design. The objectives of mix design are to achieve the desired workability, strength, durability, and cost. Basic considerations include cost, specifications, workability, strength, durability, and aggregate grading. The IS method is then described in steps, including selecting target strength, water-cement ratio, air content, water and sand contents, cement content, and aggregate contents. An example application of the IS method is also provided.
Sand is a naturally occurring granular material composed of finely divided rock and mineral particles.
the most common constituent of sand is silica (silicon dioxide, or SiO2), usually in the form of quartz.
Rate analysis and costing - Estimation, Costing and Valuation EngineeringShanmugasundaram N
Standard Data – Observed Data – Schedule of rates – Market rates – Standard Data for Man Hours and Machineries for common civil works – Rate Analysis for all Building works, canals, and Roads– Cost Estimates
The document discusses the different types of shrinkage that can occur in concrete, including plastic shrinkage, drying shrinkage, autogenous shrinkage, and carbonation shrinkage. Plastic shrinkage causes cracks on the surface of fresh concrete due to evaporation before setting. Drying shrinkage is defined as the contraction of hardened concrete from the loss of capillary water, which can lead to cracking, warping, and deflection without any external loading. In summary, the document outlines the main types of volume changes and shrinkage that concrete undergoes both during the plastic and hardened states.
Construction Materials and Engineering - Module III - Lecture NotesSHAMJITH KM
The document discusses various construction materials and methods. It covers topics like masonry, bricks, stone masonry, types of bonds, hollow block masonry, partition walls, modern construction methods, and damp proof courses. Masonry involves arranging masonry units like stone or bricks with mortar. There are different types of bonds used in brick masonry like stretcher bond, header bond, English bond and Flemish bond. Modern methods include framed construction, prefabricated construction and earthquake resistant construction. Damp proof courses are provided to prevent entry of moisture into buildings.
This document discusses different types of stone masonry and brick masonry. It describes various stone masonry techniques including rubble masonry (uncoursed, coursed random, coursed squared, polygonal, flint) and ashlar masonry (fine, rough, rock-faced, chamfered, block). It also outlines key principles for stone and brick masonry work and compares their properties and construction methods. Supervision tips are provided to ensure proper brickwork.
Cement is tested through laboratory and field tests to evaluate its properties and suitability. Key laboratory tests described in the document include:
- Fineness tests which measure particle size and surface area to determine reactivity.
- Setting time tests which ensure cement sets within specified time limits.
- Compressive strength tests where cement mortar cubes are crushed to determine strength over time.
- Soundness and loss of ignition tests which evaluate volume stability and carbon/moisture content.
Results of laboratory tests help ensure cement meets standards before use in construction projects.
1. The document classifies rocks into three main categories - igneous, sedimentary and metamorphic - based on their formation process.
2. Igneous rocks such as granite and basalt are formed by the cooling of magma. Sedimentary rocks like limestone and sandstone form through the weathering, erosion and deposition of older rocks. Metamorphic rocks like quartzite and slate form from changes to existing rocks through heat, pressure and chemically active fluids.
3. The document further subdivides rocks based on their physical and chemical properties for classification and determination of their uses as building materials.
Classification of Rocks:
- Igneous rocks form from cooled lava and include basalts and granites.
- Sedimentary rocks like sandstones and limestones form from compressed sediments.
- Metamorphic rocks like marble and slate form from heat and pressure altering igneous and sedimentary rocks.
Concrete is a widely used construction material consisting of cement, water, and aggregates. The strength of concrete is specified using its 28-day cube strength in N/sq.mm. Formwork is used to mold wet concrete into desired shapes and allow it to cure. Formwork design involves choosing traditional or systematic approaches using wood or steel components like props, beams, sheathing to form columns, walls, and beams until the concrete gains sufficient strength. Proper formwork is important for quality concrete finish and structural integrity.
Cement tests can be divided into field tests and laboratory tests. Laboratory tests include fineness test, standard consistency test, setting time test, compressive strength test, soundness test, and tensile strength test. The fineness test measures the mean size of cement grains and finer cement results in earlier strength development but more shrinkage and cracking. The standard consistency test determines the percentage of water required to form a cement paste using a Vicat apparatus. The setting time test uses the Vicat apparatus to detect when cement paste reaches its initial and final set. The compressive strength test forms cement mortar cubes which are tested at 3 and 7 days to determine strength. The soundness test uses a Le-Chatelier apparatus to
This document defines bricks and their constituents and manufacturing process. It provides the following key details:
- Bricks are clay constructions of uniform size and shape, traditionally 23cm x 11.4cm x 7.6cm or modular 19cm x 9cm x 9cm.
- Good bricks contain 50-60% silica, 20-30% alumina, up to 5% lime, and 5-6% iron oxide.
- Bricks are manufactured through processes of preparation, molding, drying for 7-14 days, and burning at 750-1000°C using clamp or kiln methods.
- Various bonds including English, Flemish, stretcher and header are used in brickwork construction
Concrete is the most widely used building material due to its low cost, fireproof and weatherproof properties, and ability to be molded into any shape. It is a composite material made of cement, water, and aggregates. Reinforced concrete is concrete strengthened with steel bars. Brick is made from fired clay and is cheap and strong in compression. Cast iron is strong but weaker than steel. Steel is one of the strongest materials and is used widely in construction. Aluminum is lightweight but expensive. Wood is cheap and moderately strong but can rot and burn easily. Plastic is flexible, lightweight, and strong in compression and tension but is expensive.
This document provides information about building stones. It begins by defining stone and rock. It then discusses different ways stones can be classified, including by geology, physical properties, chemistry, and hardness. Specific rock types that make good building stones are mentioned, such as granite, limestone, marble, and slate. The document outlines various tests used to evaluate stones, including acid resistance, water absorption, impact resistance, and crushing strength. Finally, it briefly discusses the processes of quarrying, dressing, and seasoning stones for construction.
Curing concrete is important to allow the cement hydration process to continue and develop strength over time. Proper curing ensures concrete reaches its designed strength and durability by controlling moisture loss. Common curing methods include water curing through ponding, sprinkling or wet coverings; membrane curing using plastic sheeting or curing compounds; and steam curing to accelerate strength gain. Curing should continue for at least 7 days for normal concrete and 14 days if blended cements are used. Inadequate curing can lead to reduced strength, increased permeability and poor durability.
This document provides an overview of various common building materials used in civil engineering projects. It discusses the composition, properties, uses and testing procedures for water, concrete, cement, aggregates, paints/coatings, bricks, stones, metals/steel, timber and glass. For each material, key details are given around its history, ingredients, strengths and applications in construction. Standards and quality measures are also outlined. The document serves as a basic introduction to the principal materials that civil engineers work with.
Mortar is a workable paste used to bind construction blocks together and fill gaps. It is typically made of sand, a binder like cement or lime, and water. Mortar hardens after setting to form a rigid structure. Different types of mortar are used depending on the binder, intended use, and required properties. Cement mortar provides high strength and is used for load-bearing walls. Lime mortar is used above ground, while mud mortar is a cheaper option for ordinary buildings. Special mortars include fire-resistant, lightweight, and sound absorbing varieties.
Building materials elements of civil engineeringPriyank Bhimani
The document discusses various construction materials used in civil engineering projects. It describes properties and composition of common materials like stone, bricks, lime, cement, sand and aggregate. It provides details on manufacturing processes, types and qualities required for stones, bricks and lime to be suitable for construction purposes. The mechanical and physical properties of construction materials are also outlined.
Properties of fresh and Hardened ConcreteVijay RAWAT
The document discusses various properties of fresh and hardened concrete. It describes workability, consistency, segregation, bleeding, mixing, placing, consolidating, and curing of fresh concrete. It also discusses compressive strength, tensile strength, modulus of elasticity, permeability, and durability of hardened concrete. The key properties of fresh concrete include workability, consistency, segregation, bleeding, setting time, and uniformity. Compressive strength is identified as the most important property of hardened concrete.
This document discusses the classification and properties of aggregates used in concrete. It describes three main classifications of aggregates: 1) based on unit weight as normal, heavyweight, or lightweight, 2) based on size as fine or coarse aggregate, and 3) based on shape as rounded, irregular, angular, or flaky. It then discusses various physical and engineering properties of aggregates including size, shape, strength, surface texture, specific gravity, bulk density, water absorption, and soundness. The purpose is to provide information on aggregates for use in concrete mixtures in civil engineering applications.
This document discusses various factors that affect the choice of building construction materials. It describes key properties that materials must have for different applications, including strength, resistance to water, acids, fire, weathering, frost, and durability. The document emphasizes that understanding materials' properties allows choosing the optimal material for a given service condition or climate. Standardization is also important to ensure materials meet minimum quality levels and drive industry improvement.
This document provides information on concrete mix design, including objectives, basic considerations, and the IS (Indian Standards) method for mix design. The objectives of mix design are to achieve the desired workability, strength, durability, and cost. Basic considerations include cost, specifications, workability, strength, durability, and aggregate grading. The IS method is then described in steps, including selecting target strength, water-cement ratio, air content, water and sand contents, cement content, and aggregate contents. An example application of the IS method is also provided.
Sand is a naturally occurring granular material composed of finely divided rock and mineral particles.
the most common constituent of sand is silica (silicon dioxide, or SiO2), usually in the form of quartz.
Rate analysis and costing - Estimation, Costing and Valuation EngineeringShanmugasundaram N
Standard Data – Observed Data – Schedule of rates – Market rates – Standard Data for Man Hours and Machineries for common civil works – Rate Analysis for all Building works, canals, and Roads– Cost Estimates
The document discusses the different types of shrinkage that can occur in concrete, including plastic shrinkage, drying shrinkage, autogenous shrinkage, and carbonation shrinkage. Plastic shrinkage causes cracks on the surface of fresh concrete due to evaporation before setting. Drying shrinkage is defined as the contraction of hardened concrete from the loss of capillary water, which can lead to cracking, warping, and deflection without any external loading. In summary, the document outlines the main types of volume changes and shrinkage that concrete undergoes both during the plastic and hardened states.
Construction Materials and Engineering - Module III - Lecture NotesSHAMJITH KM
The document discusses various construction materials and methods. It covers topics like masonry, bricks, stone masonry, types of bonds, hollow block masonry, partition walls, modern construction methods, and damp proof courses. Masonry involves arranging masonry units like stone or bricks with mortar. There are different types of bonds used in brick masonry like stretcher bond, header bond, English bond and Flemish bond. Modern methods include framed construction, prefabricated construction and earthquake resistant construction. Damp proof courses are provided to prevent entry of moisture into buildings.
This document discusses different types of stone masonry and brick masonry. It describes various stone masonry techniques including rubble masonry (uncoursed, coursed random, coursed squared, polygonal, flint) and ashlar masonry (fine, rough, rock-faced, chamfered, block). It also outlines key principles for stone and brick masonry work and compares their properties and construction methods. Supervision tips are provided to ensure proper brickwork.
Cement is tested through laboratory and field tests to evaluate its properties and suitability. Key laboratory tests described in the document include:
- Fineness tests which measure particle size and surface area to determine reactivity.
- Setting time tests which ensure cement sets within specified time limits.
- Compressive strength tests where cement mortar cubes are crushed to determine strength over time.
- Soundness and loss of ignition tests which evaluate volume stability and carbon/moisture content.
Results of laboratory tests help ensure cement meets standards before use in construction projects.
1. The document classifies rocks into three main categories - igneous, sedimentary and metamorphic - based on their formation process.
2. Igneous rocks such as granite and basalt are formed by the cooling of magma. Sedimentary rocks like limestone and sandstone form through the weathering, erosion and deposition of older rocks. Metamorphic rocks like quartzite and slate form from changes to existing rocks through heat, pressure and chemically active fluids.
3. The document further subdivides rocks based on their physical and chemical properties for classification and determination of their uses as building materials.
Classification of Rocks:
- Igneous rocks form from cooled lava and include basalts and granites.
- Sedimentary rocks like sandstones and limestones form from compressed sediments.
- Metamorphic rocks like marble and slate form from heat and pressure altering igneous and sedimentary rocks.
The document discusses different types of stones used in construction. It describes various stone materials including granite, basalt, sandstone, limestone, laterite, quartzite, marble, slate, flagstone, and rubble. The document outlines the geological and physical classification of stones. It discusses the quarrying, dressing, preservation, and construction techniques used for stone, including paneling, ashlars, and rubblework. Common applications of stone include use in exterior cladding, flooring, countertops, and roofing.
This document provides information on engineering materials used in building construction. It discusses properties of materials like strength, elasticity, and hardness. It also covers various building materials like stones, bricks, tiles, cement, sand and mortar. Specific types of stones found in Bangladesh and their uses are outlined. Methods of quarrying and testing properties of building materials are described. Foundation types, brickwork, floors, roofs, masonry, and stairs are also summarized.
Types, importance and uses of rocks inSameer Nawab
This document discusses the types, importance, and uses of rocks in construction. It outlines three main types of rocks - igneous, sedimentary, and metamorphic - and describes their formation processes. It then discusses specific rock types like granite, limestone, sandstone, and marble, outlining their common construction applications like buildings, monuments, and bridges. The document emphasizes the importance of understanding a rock's properties for determining appropriate construction uses and foundations. Proper geological analysis is important for engineering projects to be built safely and economically.
This document discusses building materials and stones. It begins by classifying rocks into three categories: igneous, sedimentary, and metamorphic. It then discusses the physical, chemical, and geological classifications of rocks. Various types of stones are described along with their properties and common uses. Requirements for good building stones include strength, durability, workability, appearance, and weather resistance. Key characteristics that determine the quality of building stones are also outlined such as structure, hardness, texture, specific gravity, porosity, and natural bed.
This document discusses rocks and minerals. It defines them as natural hard substances formed from minerals like quartz and mica. It describes different types of rocks such as granite, basalt, and limestone. It then covers the physical properties used to identify rocks, including hardness, cleavage, streak, lustre, and crystal formation. Different categories of rocks are outlined, including igneous rocks formed from volcanic activity, sedimentary rocks formed by deposition of particles, and metamorphic rocks formed by changes to pre-existing rocks. Specific rocks like granite and marble are discussed in more detail. Uses of rocks in construction are also summarized.
The document discusses various building construction materials used in civil engineering projects, including natural stones like granite, limestone, and sandstone as well as artificial materials like concrete blocks. It provides details on classifying and selecting stones based on their properties, describing the appropriate uses of different stone types in constructions like buildings, dams, roads, and more. Common stones are evaluated based on factors like strength, hardness, durability, and workability to determine their suitability for structural or decorative applications.
The document discusses the three main types of rocks: igneous, sedimentary, and metamorphic. It provides details on their origin, formation process, structure, texture, types, and examples. Key differences are noted - igneous rocks form from cooled lava/magma, sedimentary rocks form from compressed sediments, and metamorphic rocks form from changes to existing rocks due to heat and pressure. The conclusion states the three rock types can be identified by their characteristics but may also transition between types through the rock cycle.
Rocks can be classified as igneous, sedimentary, or metamorphic based on their formation. Igneous rocks form from cooling lava, sedimentary rocks form from compressed sediments, and metamorphic rocks form from changes to existing rocks by heat and pressure. Common rocks used for construction include granite, limestone, sandstone, quartzite, slate, and marble. Each has distinct properties making it suitable for uses like flooring, walls, countertops, or roofing. Proper testing ensures rocks meet requirements for strength, durability and appearance for their intended application in buildings.
STONE -As A Building Material.
Stones have been considered as one of the popular building material from the olden days due to their availability in abundance from the natural rocks. Building stones should possess enough strength and durability.
The stones which are suitable for the construction of the structures such as retaining walls, abutments, dams, barrages, roads etc are known as building stones.
TR 231 GEOLOGY FOR CIVIL ENGINEERING soil.pdfHenryAlex13
1) This document discusses soil mechanics and soil classification. It covers soil formation, composition, properties, classification systems, and testing methods.
2) Soils are classified based on their formation process, particle size distribution, plasticity, and organic content. Methods of testing include sieve analysis, hydrometer analysis, and determining Atterberg limits.
3) Several soil classification systems exist, with the Unified Soil Classification System being adopted. Soils are classified as gravel, sand, silt, clay, or organic based on particle sizes and plasticity.
Stone has been used widely in historical structures due to its strength and durability. The document discusses the various uses of stone in construction, including residential and public buildings, dams, bridges, and as an aggregate in concrete. It also covers the classification, quarrying, dressing, and preservation of stones. Various tests are conducted on stones to determine their suitability for different engineering applications based on properties like strength, durability, and resistance to weathering.
BMCT Mumbai University Module 2 Building Materials.pptxSachinPawarUCOE
This document discusses building materials used in construction, focusing on different types of stones. It begins by classifying stones based on their geological formation - igneous, sedimentary, or metamorphic rocks. It then discusses physical and chemical classifications of stones. Common uses of building stones and qualities of good building stones are outlined. Finally, various tests conducted on stones to determine properties like hardness, durability, porosity, and resistance to weathering are summarized.
The document discusses stone as a building material. It classifies rocks geologically into igneous, sedimentary, and metamorphic rocks. It then describes common types of rocks used in construction like granite, sandstone, limestone, marble, and slate. It outlines characteristics of good building stones such as hardness, durability, porosity, and resistance to decomposition. Finally, it discusses common uses of building stone and types of stone flooring and masonry walls.
This document discusses building stones used in civil engineering. It defines building stone as a construction material derived from rocks in the earth's crust. Some key historical structures that used building stones are mentioned, such as the pyramids of Egypt and the Taj Mahal. The document also discusses the classification, characteristics, quarrying and uses of different types of building stones including igneous, sedimentary and metamorphic rocks. Good building stones are described as having properties like uniform appearance, strength, hardness, porosity and weathering resistance.
This document discusses building stones used in civil engineering. It defines building stone as a construction material derived from rocks in the earth's crust. Some key historical structures that used building stones are mentioned, such as the pyramids of Egypt and the Taj Mahal. The document also discusses the classification, characteristics, quarrying and uses of different types of building stones including igneous, sedimentary and metamorphic rocks. Good building stones are described as having properties like uniform appearance, strength, hardness, low porosity and weathering resistance.
This document discusses various types of construction materials used in civil engineering projects. It covers the key materials used like stone, bricks, cement, aggregates, steel, and timber. It also summarizes the roles and responsibilities of civil engineers in activities like design, construction, supervision, and maintenance of structures. Finally, it provides classifications and properties of different types of stones commonly used in construction.
Stone and Details about the stone and types of all natural and man-made .pdfttasharmishthawakcha
The document provides information about different types of stone, including their formation, classification, and uses. It discusses natural stones such as granite, marble, limestone, and sandstone that were formed by geological processes over millions of years. It also describes man-made stones like agglomerate, faux marble, and terrazzo that are composite materials produced by binding stone chips. The document outlines various tests conducted on stones and preservation methods used to increase their lifespan. It discusses the applications of both natural and man-made stones in construction, architecture, interior and landscape design.
Similar to Construction Materials and Engineering - Module I - Lecture Notes (20)
Construction Materials and Engineering - Module IV - Lecture NotesSHAMJITH KM
The document discusses various basic components of building construction including substructure, superstructure, foundation, plinth, beams, columns, walls, arches, roofs, slabs, lintels, parapets, staircases, doors, windows and other elements. It provides descriptions of each component, their functions and materials typically used. Foundations discussed include isolated spread footing, wall/strip footing, combined footing, cantilever/strap footing and mat/raft footing for shallow foundations and pile, well/caisson and pier foundations for deep foundations. Flooring materials and requirements are also summarized along with technical terms for doors and windows.
Construction Materials and Engineering - Module II - Lecture NotesSHAMJITH KM
This document provides information on various construction materials including paints, plastics, rubber, and aluminum. It discusses the ingredients, properties, types, and applications of paints. It also outlines the classification, characteristics, uses, advantages, and limitations of plastics. Details are provided on types of rubber like natural and synthetic rubber. Applications of aluminum in construction are also mentioned.
Computing fundamentals lab record - PolytechnicsSHAMJITH KM
The document is a lab record for a computing fundamentals course. It contains instructions for students on proper lab conduct and procedures. It also outlines 25 experiments to be completed, covering topics like computer hardware, operating systems, word processing, spreadsheets, programming, and calculations. General instructions are provided for safety and proper use of equipment in the computing lab.
Cement is a binding agent that undergoes hydration when mixed with water. There are various types of cement including ordinary Portland cement (OPC), rapid hardening cement, and sulphate resisting cement. Cement provides early strength through C3S and later strength through C2S. Heat is generated during cement hydration through an exothermic reaction. Proper storing, grading of aggregates, minimizing segregation, and adding admixtures can improve the properties of concrete.
നബി(സ)യുടെ നമസ്കാരം - രൂപവും പ്രാര്ത്ഥനകളുംSHAMJITH KM
- \_n(k) regularly led prayers and provided guidance during prayer gatherings.
- He taught to pray with humility and focus, avoiding idle thoughts or actions that distract from prayer.
- The summary provides guidance on proper prayer etiquette like standing, bowing, and order of movements based on hadith sources.
Design of simple beam using staad pro - doc fileSHAMJITH KM
The document describes designing a simple beam using STAAD.Pro software. It involves generating the beam geometry, applying loads and supports, analyzing the beam, and reviewing the results, which include the loading diagram, shear force diagram, bending moment diagram, deflection pattern, input file, concrete takeoff, and concrete design details. The key steps are 1) creating the beam model in STAAD.Pro, 2) applying the loading and support conditions, 3) analyzing the beam, and 4) reviewing the output results.
The document describes designing a simple beam using STAAD.Pro software. It involves generating the beam geometry, applying loads and supports, analyzing the beam, and designing the beam for concrete. Key steps include assigning the beam properties, applying a fixed support at one end and distributed and point loads, obtaining the loading diagram, shear force and bending moment diagrams, and running the concrete design. The output includes structural drawings, input files, concrete takeoff, and beam design details.
Python programs - PPT file (Polytechnics)SHAMJITH KM
The document discusses various Python programming concepts like addition, subtraction, average, volume calculations, conversions between Celsius and Fahrenheit, finding the largest of three numbers, determining if a number is odd or even, printing natural numbers up to a limit, and calculating the factorial of a number. Algorithms, flowcharts and Python code are provided for each concept as examples.
Python programs - first semester computer lab manual (polytechnics)SHAMJITH KM
The document contains Python algorithms and programs for various mathematical and logical operations like addition, subtraction, average, largest number, factorial, etc. Each section includes the algorithm, flowchart and Python code with sample output for each operation.
Python programming Workshop SITTTR - KalamasserySHAMJITH KM
This document provides an overview of Python programming. It begins with an introduction and outlines topics to be covered including what Python is, its features, basics of syntax, importing, input/output functions, and more. Various Python concepts and code examples are then presented throughout in areas such as data types, operators, decision making with if/else statements, loops (for and while), functions, and classes. Examples include calculating square roots, the volume of a cylinder, checking for prime numbers, and a multiplication table. The document serves as teaching material for a Python programming course.
Analysis of simple beam using STAAD Pro (Exp No 1)SHAMJITH KM
The document describes analyzing a simple beam using STAAD.Pro software. It discusses the steps taken, which include generating the beam model geometry by adding nodes and a member, specifying member properties and support types, applying loads, performing analysis, and viewing the results in the form of structure diagrams showing values like bending moment and shear force. The overall aim was to familiarize the user with STAAD.Pro's interface and analyze a basic beam structure.
This document contains questions and answers related to Computer Aided Drafting (CAD). It defines key CAD terms like AutoCAD, CAD, CADD and lists common CAD software packages. It describes the applications of CAD and shortcuts for common AutoCAD commands. The document also discusses CAD concepts like layers, blocks, arrays, rendering and perspectives. It provides standard paper sizes and outlines the model procedure for creating a CAD drawing in AutoCAD.
Brain Computer Interface (BCI) - seminar PPTSHAMJITH KM
This document discusses brain computer interfaces (BCI). It begins by providing background on early pioneers in the field like Hans Berger in the 1920s-1950s. It then discusses some key BCI developments from the 1990s to present day, including devices that allow paralyzed individuals to control prosthetics or computers using brain signals. The document outlines the basic hardware and principles of how BCIs work by interpreting brain signals to control external devices. It discusses potential applications like internet browsing, gaming, or prosthetic limb control. The benefits and disadvantages of BCIs are noted, and the future possibilities of using BCIs to enhance human abilities are explored.
Surveying - Module iii-levelling only noteSHAMJITH KM
This document defines levelling and its key terms like datum, mean sea level, bench mark, level surface, and level line. It describes levelling instruments like the dumpy level, wye level, and tilting level. It explains self-reading staffs, target staffs, and how to take readings. It discusses errors in levelling, curvature and refraction corrections, and methods for reducing levels including the height of instrument and rise-and-fall methods. Temporary adjustments to levelling instruments are also outlined.
Surveying - Module II - compass surveyingSHAMJITH KM
The document provides information on compass surveying. It defines terms like traverse, compass surveying, bearing, fore bearing, back bearing, closed traverse, open traverse, local attraction and its sources. It discusses instruments used like compass, theodolite, sextant. It explains concepts like true bearing, magnetic bearing, arbitrary bearing, meridian, declination, dip. Methods to detect and correct for local attraction and closing error in closed traverse are outlined. Differences between prismatic compass and surveyor's compass are tabulated. Various questions and their answers on these concepts are provided.
Surveying - Module I - Introduction to surveying SHAMJITH KM
This document provides an overview of surveying techniques and concepts. It defines surveying, lists its primary objectives, and describes the main divisions of surveying as plane surveying and geodetic surveying. The document also discusses concepts like ranging, chaining, triangulation, obstacles in surveying, plane table surveying methods, and accessories used in plane table surveying. In addition, it provides examples of chain survey field book pages and procedures for solving problems in plane table surveying.
We have designed & manufacture the Lubi Valves LBF series type of Butterfly Valves for General Utility Water applications as well as for HVAC applications.
Better Builder Magazine brings together premium product manufactures and leading builders to create better differentiated homes and buildings that use less energy, save water and reduce our impact on the environment. The magazine is published four times a year.
An In-Depth Exploration of Natural Language Processing: Evolution, Applicatio...DharmaBanothu
Natural language processing (NLP) has
recently garnered significant interest for the
computational representation and analysis of human
language. Its applications span multiple domains such
as machine translation, email spam detection,
information extraction, summarization, healthcare,
and question answering. This paper first delineates
four phases by examining various levels of NLP and
components of Natural Language Generation,
followed by a review of the history and progression of
NLP. Subsequently, we delve into the current state of
the art by presenting diverse NLP applications,
contemporary trends, and challenges. Finally, we
discuss some available datasets, models, and
evaluation metrics in NLP.
Sri Guru Hargobind Ji - Bandi Chor Guru.pdfBalvir Singh
Sri Guru Hargobind Ji (19 June 1595 - 3 March 1644) is revered as the Sixth Nanak.
• On 25 May 1606 Guru Arjan nominated his son Sri Hargobind Ji as his successor. Shortly
afterwards, Guru Arjan was arrested, tortured and killed by order of the Mogul Emperor
Jahangir.
• Guru Hargobind's succession ceremony took place on 24 June 1606. He was barely
eleven years old when he became 6th Guru.
• As ordered by Guru Arjan Dev Ji, he put on two swords, one indicated his spiritual
authority (PIRI) and the other, his temporal authority (MIRI). He thus for the first time
initiated military tradition in the Sikh faith to resist religious persecution, protect
people’s freedom and independence to practice religion by choice. He transformed
Sikhs to be Saints and Soldier.
• He had a long tenure as Guru, lasting 37 years, 9 months and 3 days
8. Residual
Types of Deposits
Sedimentary OrganicChemical
fine weathered particles get washed away
weathered coarser particles
remains in the origin site and sets in layers
Parent rock
17. Stratified Unstratified Foliated
Physical classification
Can easily split along
planes of cleavage
Eg:-
Sedimentary rocks
Distinct layers
Compact crystalline
Can’t split in desired
layers.
No distinct layers
Eg:-
Igneous rocks
Layered structure
Split easily along
planes of foliation.
Eg:-
Metamorphic rocks
Sedi.rocks MetaMor
18. Siliceous Argillaceous Calcareous
Chemical classification
Eg:-
Granite, Quartzite
High silica content High clay/Alumina
content
Eg:-
Slate, Laterite
Clay minerals
- Kaolin, Illite
- Montmorillonite
High CaCO3 content
Eg:-
Limestone, Marble
High fire resistance
19. Classification of rocks
Geological Physical Chemical
1) Igneous rocks
2) Sedimentary rocks
3) Metamorphic rocks
1) Stratified rocks
2) Unstratified rocks
3) Foliated rocks
1) Siliceous rock
2) Argillaceous rocks
3) Calcareous rocks
- Formed by cooling of magma
- Eg:- Granite, Dolerite, Basalt
- Due to weathering action of
water, wind and frost
- Eg:- Gravel, Gypsum, limestone
- Formed by change in character
of existing rocks when subjected
to heat and pressure
- Eg:- Quartzite, slate, marble
- Have planes of cleavage
- Can split into layers
- Eg:- Sedimentary rocks
- No distinct layers
- Eg:- Igneous rocks
- Rocks having a tendency to split up
in a definite direction only
- Eg:- Metamorphic rocks
- High silica content
- Eg:- Granite, Quartzite
- High clay content
- Eg:- Slate, Laterite
- High CaCO3 content
- Eg:- Marble, Lime stone
- Durability depends on
surrounding materials
Plutonic, Hypabyssal, Volcanic
20. Note:
Shingle – decomposed laterite
Diamond – Kimberlite (Igneous rock) – Hardest rock
Talc – Softest rock
Gneiss is obtained from sedimentary metamorphic rocks
21. Crushing Strength
Characteristics of a good building stone
1 > 100 N/mm2
Appearance2
Durability3
Fracture4
Hardness5
Uniform colour
Long lasting in changing weather conditions
Sharp, even and clear fracture
> 17 = Hard = used in roads
14-17 = Medium hardness
< 14 = Poor Hardness
Percentage wear6 ≤ 3 %
22. Characteristics of a good building stone
Good Fire resistance7
Specific gravity8
Texture9
> 2.7
Have compact fine crystalline structure
Should be free from cavities, cracks or patches
Seasoning11 Upto 6-12 months
Toughness index12
Water absorption10 % absorption by weigth after 24 hours
should not exceed 0.60
< 13 = not tough
13-19 = Moderate
>19 = High- Impact test
23. Varieties of stones
Granite
• Igneous rock – Plutonic
• Composed of quartz + feldspar + Silica
• Available in colors: Grey, Green, Brown, Pink, Red
• Hard, durable, high resistance to weathering
• Specific gravity = 2.7
• Compressive strength = 700 – 1300 N/mm2.
• Uses: Ornamental works, flooring, walls etc
24. Varieties of stones
Trap rock
• Igneous rock - Volcanic
• Dark colour
• Specific gravity = 2.8 – 3.0
Eg:- Basalt
Uses : As crushed rocks,
railway ballast
25. Varieties of stones
Basalt
• Igneous rock - Volcanic
• Compact, Hard
• Colour: Red, Yellow, Grey, Blue
• Specific gravity = 3
• Compressive strength = 1530 – 1890 N/mm2.
• Uses: aggregates for concrete, ornamental works
26. Varieties of stones
Sand Stone
• Sedimentary rock
• Fine/coarse grained
• Specific gravity = 2.65 – 2.95
• Compressive strength = 650 N/mm2.
• Used for Ashlar works
27. Varieties of stones
Laterite
• Sedimentary rock
• Hard and durable
• Rich in Fe and Al
• Colour : Rusty red
(high iron oxide content)
• Uses: Building blocks
29. Quarrying of stones
Process of extracting or taking out stones
from natural rock beds.
Quarry – Exposed surface of a natural rock
Quarry Site – Site from where stones are taken
30. • Availability – tools, materials and labour
Selection of quarry site
• Quality of building stone should not vary with depth
• Distance should be min from transportation facilities
• Space for disposal of refuse and quarry wastes - near
• Geological information about the site
• Availability of water
• No health hazards at site
• Results of trial pits
31. Methods of quarrying
With hand tools With channelling
machine
By blasting
1) Digging/Excavating
2) Heating
3) Wedging
- For digging soft stones
- Hand tools: pick axle,
hammer, shovel, chisel, etc
- Differential expansion separates
upper layer from lower layer
- In rocks with cracks and fissures
- Steel wedges are used
- Cut channels of sufficient depth
along three sides
- There should be an exposed face
other than top face.
- Horizontal holes are driven beneath
the block from exposed face.
- Block is lifted from its bed.
Eg:- Granite, Marble
- Operations involved:
1. Boring
2. Charging
3. Tamping
4. Firing
- Produce irregular sized stones
- Explosives used to blast rocks
- When rock is hard and unfissured
32.
33. Detonators Explosives Fuses
- Whose explosion
initiates explosion
of another
Materials for blasting
- To ignite explosives
- Used when dynamite
is used as explosive
- Fired either by fuse
or spark
- Dynamite and
Blasting powder
(Gun powder)
Charcoal
Saltpetre (KNO3)
Sulphur
Sandy powder (25%)
Nitro-glycerine (75 %)
- Use: Ordinary
quarrying works
- Uses: Tunnelling
Mining operations
Under water quarrying
- Small rope of cotton with
a core of continuous
thread of gun powder
34. Other explosives used in blasting:
1. Gelatine – 50 % more powerful than dynamite
2. Cordite – under water, no smoke
3. Gelignite – under water
4. Gun cotton
5. Liquid oxygen – large scale (mining, under water)
6. Rock-a-rock
35. • Quarried stones are cut into suitable size and shape
Dressing of stone
• To Provide pleasing appearance
• To provide good horizontal and vertical joints in masonry
• To make transportation easier
• To obtain good bonding
Types of dressing
1. Quarry dressing
2. Site dressing
36. Deterioration of stones
1. Alternate wetness and drying
2. Frost
3. Impurities in atmosphere
4. Living organisms
5. Movement of chemicals
6. Rain water
7. Temperature variations
8. Vegetable growth
9. Wind
37.
38. Clay Products2
Ceramics Potter’s art
Articles made by the potter(‘Keramos’-Greek)
Clay products Refractories Glass
Clay Products
41. Composition of brick earth:
1 Alumina 20-30 %
Chief constituent
imparts plasticity
Excess – shrinkage and warping
2 Silica 50-60 %
Prevent cracking, shrinking & warping
Imparts uniform shape to bricks
Durability of bricks depends mainly
3 Lime < 5%
Prevents shrinkage
Excess – lime melts and shape losts
4 Iron Oxide 5-6 %
Helps lime to fuse sand
Imparts red colour
Excess – blackish, less - yellowish
5 Magnesia Small quantities
Imparts yellow tint
Reduce shrinkage
Excess – decay of bricks
42. Alkalis – deform and twist brick
Harmful ingredients in brick earth
Lime – on heating converted into quick lime – brittle crumbles
Iron pyrites
Pebbles
Vegetation and organic matter
43. Manufacturingofbricks
1.Preparation of clay
Unsoiling
Digging
Cleaning
Weathering
Blending
Tempering or pugging
2. Moulding
Hand moulding
Machine moulding
3. Drying
Natural
Artificial
4. Burning
Clamp burning
Kiln burning
Operations involved
- Removing top 20 cm clay layer
- Impurities, trees, etc are removed
- Manually or using power excavators
- Roots, pebbles, lime, organic matter
- Softening clay by adding little water
and exposing to atmosphere
- Tests for suitability
- Kneading by adding water to get a
Homogenous mass & reqd plasticity
45. 2. Moulding
Hand moulding Machine moulding
• Rectangular boxes of wood or steel
• Clay placed in the machine
• it comes out through the
opening under pressure.
• It is cut to bricks by steel
wires fixed into frames.
• Open at top and bottom
1. Ground moulded bricks
2. Table moulded bricks
1. Plastic clay machines
2. Dry clay machines
Classification:
Classification:
46. Natural Drying Artificial Drying
• To avoid cracks and distortion • To avoid cracks and distortion
• Drying by tunnels usually
1200C about 1 to 3 days
• Good circulation of air
• In a drying yard
• Machine arrangements
Wet mix contain
7-30 % moisture
3. Drying
50. • Trapezoidal shape
• End raised at 150 from ground level
• Brick wall in mud at short end
• Alternate layers of raw bricks and fuels.
• Fuels - grass, cow dung, wood
• Air circulation spaces provided
• Total height of clamp = 3-4 m
• Plastered with mud on sides and top,
filled with earth to prevent the escape of
heat
• Burning Period = 1-2 months
• Cooling period = 1-2 months
• Burnt bricks are taken out from the
clamp
51. Advantages
• Tough and strong bricks burning and cooling are gradual
• Cheap and economical
• No skilled labour and supervision required
• Saving of clamps fuel
Disadvantages
• Bricks are not of required shape
• It is very slow process
• It is not possible to regulate fire in a clamp
• Quality of brick is not uniform
53. Kiln burning • A kiln is a large oven to burn bricks
• 2-3 brick row
• Trolleys used for movement of bricks
• Loading of kiln with raw bricks
• Each door is built up with dry bricks and
are covered with mud or clay
• Fire period = 48 to 60 hours
• Cool period = 12 days
• Bricks are then taken out
• Same procedure is repeated for the next
burning
Intermittent kilns
54. Advantages of kiln burning
• Bricks are evenly burnt
• Performance of this kiln is better
• Suitable for burning of structural clay tiles, terra cota close control of
heat
55. • Rectangular, circular or oval
• Trench excavated in ground
• Widely used kiln in India
Continous kilns
Bull’s trench kiln Hoffman’s kiln Tunnel kiln
• Also called flame kiln
• Plan – circular shape
• Permanent roof provided
• Function in Rainy season also
• Form of a tunnel
• Straight, circular or oval
• Trolley transportation
• Large scale - economical
56.
57. Comparison of clamp and kiln burning
Clamp burning Kiln burning
1 Capacity 2000 - 100000 Avg = 25000
2 Cost of fuel Low – grass, cow dung, wood High - coal
3 Initial cost Less More – Permanent structure
4 Quality Good = 60 % Good = 90 %
5 Fire regulation Not possible to control Possible
6 Skilled supervision No Yes
7 Structure Temporary Permanent
8 Suitability Small scale Large scale
9 Burning time 1-2 months 2-3 days
10 Cooling time 1-2 months 12 days
58. Unburnt bricks
IS specifications of bricks
• Sun dried bricks
(Classification)
Burnt bricks
• Used only in the
constructions of
temporary and cheap
structures
• Heavy rains - X
First class
Second class
Third class
Fouth class
• For good and permanent works
• Brick work + plastering works
• Unimp and temp structures
• over burnt bricks with irregular
shape and dark colour
• Ringing sound
• Bad ringing sound
• Rough and slightly irregular
59. 1. Free from cracks and have sharp edges
Characteristics of good brick
2. Uniform shape and size
3. Should give clear ringing sound when struck each other
4. Compact and free from voids
5. Bricks should not absorb water when soaked for 24
hours • 1st class max = 20 percent by weight
• 2nd class max = 22 percent by weight
60. 6. No impression when scratched
7. Low thermal conductivity
8. When fall from 1 m height should not break
9. Crushing strength > 55 kg/cm2
10. Sound proof
Characteristics of good brick
63. Tiles
Thin slabs of bricks which are burnt in kilns
Thinner than bricks ⸫ handle carefully
Bricks may be glazed or unglazed
They are incombustible in nature
Tiles are unaffected under light
64. Manufacture of tiles
Fine clay is usedPreparation of clay
Moulding
Drying
Burning
1
2
3
4
Clay is pressed in Pattern/Shapes
Drying under a shade prevents warping
and cracking of tiles due to rain and sun
Sialkot kiln
65.
66. Characteristics of a good tile
Free from cracks and bends1
Regular in shape and size2
Well burnt, hard and durable3
Gives clear ringing sound when struck with hand4
Fit properly when placed in position5
Uniform colour and compact structure6
67. Types of tiles
1. Roofing tiles
2. Flooring tiles
3. Wall tiles
4. Partition tiles
5. Pavement tiles
6. Drain tiles
Based on application Material & Manufacture
1. Ceramic tiles
a) Earthenware tiles
b) Terracotta and faience
c) Fully vitrified tiles
d) Glazed tiles
e) Stoneware Tile
2. Porcelain tiles
3. Mosaic tiles
4. Natural stone tiles
68. 1. Roofing tiles
To keep out rain
Shelter
Made of clay/slate
Modern materials :
concrete and plastic
Eg: Flat tile
Eg: Flat tile
Types of roofing tiles
Allahabad tiles1
Corrugated tiles2
Flat tiles3
Manglore tiles4
Pan tiles5
Pot tiles5
Semi-circular
Double channeled
Basel Mission
Manglore Pattern
69. 2. Floor tiles 3. Wall tiles
Made of ceramic, stone,
or glass
Available in various
textures
Interior and exterior
walls
Decoration purpose
Toilets
Used for flooring works
Flat in shape
4. Drain tiles
Drain water through it
Tiles with holes
Porous
Avoids flooding of water
70. 5. Partition tiles 6. Pavement tiles
Used for partition of spaces in a room
Thinner partitions
Sub divide areas into room
Used as pavements
Provision for drainage
Also called as inter-locks
71. 1. Ceramic tiles
Clay, sand, and other natural substances.
Commonly used in residential buildings
Mainly used in interior walls and floors
Ceramic coating
Clay
72. 2. Porcelain tiles
A type of ceramic tiles
Clay grains used are finer than ceramic tiles
Mainly used in interior walls and floors
Fired at higher temperature than ceramic tiles
Denser, less porous and more resistant to
moisture and stains than ceramic tiles
Suitable for both indoor and outdoor works
Harder, but low water absorption
73. Vitrified tiles Glazed tiles
Clay + quartz + feldspar + silica
Alternative to marble and granite
flooring
Liquid glass coating of
thickness 0.1 - 0.2 mm
Stain resistant
Ceramic tile with very low porosity
Easy to clean
Fade resistanceCeramic material in full thickness
Ceramic coating
Clay Vitrified tiles
74. 3. Terra-cotta
Terra – “earth”, cotta – “based”
Also called as “Baked earth”
Clay product made by careful burning
A kind of earthware which is soft and porous
High Alumina and iron oxide content
Less proportion of sand and lime
75. Manufacture of terra-cotta
Crushed pottery usedPreparation of clay
Moulding
Drying
Burning
1
2
3
4
Zinc + Plaster of paris
Muffle furnace
76.
77. Varieties of terra-cotta
1. Porous terra-cotta
2. Polished (fine) terra-cotta
Wood powder/saw dust added
Fire and sound proof
Also known as fine terra-cotta or Faience
Ornamental purpose
terra-cotta
Biscuiting
Heating at 650oC Immerse in
glazing compounds
Heating at 1200oC
Top surface glazed
Salt/lead solution
78. Earthenware
Ware means articles
Clay + Sand + Crushed pottery
Generally soft and porous
Clay burnt at low temperature and cooled slowly
Terra-cotta is a kind of earthenware
Uses: Ordinary drain pipe, pottery, vessels
79.
80. Stoneware
Generally Hard and non-porous
Clay burnt at high temperature and cooled slowly
Uses: Sanitary appliances, closets, wash basins, pipes
Can easily clean
81. Attribute Earthenware Stoneware
Temperature of
baking
low high
Cooling Slowly Slowly
Porosity Porous Non-porous
Hardness Soft Hard
Durable Less More
Expense Less More
Comparison of Earthenware and Stone ware
82. Porcelain (Whiteware)
Clay + felspar + Quartz + minerals
Fine earthenware – white and semi transparent
Uses: Sanitarywares, electric insulators, storage vessels
Hard, brittle and non-porous
Two types
1. Low voltage porcelain – prepared by dry process
2. High Voltage porcelain – prepared by wet process
83.
84. 84
• Important cementing material
• Used in old times instead of cement
• Uses:
Ordinary buildings
Massive monuments
Palaces
Forts
• Chemically: CaO
Lime
85. 1. Limestone hills
2. Seashells
3. Corals
4. Kankar (Below ground level)
5. Beds of old rivers
Sources of lime
86. Important technical terms
1. Calcination
Heating to redness in presence of air
2. Hydraulicity
Ability to set in presence of water and in absence of air
3. Lime
CaCO3 CaO + CO2
Calcination
(Limestone) (Lime)
Note: CaCO3 Most stable form of lime
Impurity in lime = clay
87. Important technical terms
4. Slaking
Chemical reaction occurring when water is added to lime
5. Setting
Process of hardening of lime after it has been converted
into paste form.
Ca(OH)2CaO + H2O Slaking
(Slaked lime)(Lime)
Note: Slaked lime is used for white washing
89. Classification
1. Quick (Fat/pure) lime
2. Hydraulic (Slaked) lime
3. Poor (lean) lime
Class A
Class B
Class C
Class D
Class E
Based on clay content BIS Classification
90. 1. Quick (Fat/Pure/Caustic) lime
Product left immediately after calcination of pure lime stone
Clay content – less than 5 %
Also known as white lime, rich lime, high calcium lime, etc
When slaked, volume increases by 2-2.5 %
No hydraulicity
To get hydraulicity, add Surkhi (powder of burned bricks)
91. 2. Hydraulic (Slaked/water) lime
Clay content – 10 to 30 %
Feebly H.L Moderately H.L Eminently H.L
Clay content – 5 to 10 %
Slaking is faster
(few minutes)
Setting is slow (3 week)
Used for ordinary
masonry works
Clay content – 11 to 20 %
Slakes after 1 to 2 hours
Setting is moderate
(1 week)
Used for superior type
masonry works
Clay content – 21 to 30 %
Slakes with difficulty
Setting is fast (1 day)
Used for under water
works, damp places, etc
More strength (Similar to
ordinary cement)
92. 3. Poor (lean lime)
Also known as “impure lime”
Clay content – greater than 30 %
93. BIS Classification of lime
1. Class A
2. Class B
3. Class C
4. Class D
5. Class E
6. Class F
- Eminently H.L – Structural purposes
- Semi H.L – Masonry works
- Fat lime – White washing
- Mg/Dolomite lime – finishing coat in plastering
- Kankar – masonry mortar, soil stabilization
- Silicious dolomite lime – under coat and finishing
coat in white washing
94.
95. Cement - Any substance which acts as a
• Invented by Joseph Aspidin
• Obtained by burning and crushing of stones
• Resembles natural lime
Cement
binding agent for materials
96. Ingredients and Sources
Lime : limestone, chalk, shells, shale or calcareous rock
Silica : from sand, old bottles, clay or argillaceous rock
Alumina : from bauxite, recycled Aluminum, clay
Iron : from clay, iron ore, scrap iron and fly ash
Gypsum : found together with limestone
97. Ingredients in cement
1 Lime CaO 62 %
• Binding property and strength
• excess makes cement unsound
• Deficiency – Quick setting of cement
• Lime ↑ Slow setting
2 Silica SiO2 22 %
• C2S, C3S – Strength contribution
• Excess – Strength ↑ , Prolong setting time
3 Alumina Al2O3 5 %
• imparts quick setting property
• Act as a flux to reduce clinkering
temperature (2000oC 1500oC)
• Produce more heat at time of hydration
4 Calcium Sulphate CaSO4 4 %
• Gypsum - increase the initial setting time
• Added to rotary kiln at time of final grinding
5 Iron oxide Fe2O3 3 % • imparts colour, Hardness and strength
6 Magnesia MgO 2 % • Yellowish tint, excess unsound
7 Sulphur S 1 % • excess makes cement unsound
8 Alkalies … 1 % • Excess cause efflorescence
106. Calcination - Burning a mixture of calcareous and
argillaceous material at very high temperature
in correct proportion.
Calcined product = CLINKER
CLINKER + Gypsum = cement
107. Characteristics of cement
High compressive strength
Flexible and easy mouldable
Easy to handle and use
Good binding property
Cement never gets rusted
Cement is a bad conductor of electricity
109. 8. Low Heat Cement
9. Portland Pozzolana Cement – fly ash based and calcined clay based
10. Air Entraining Cement
11. Coloured Cement (White Cement/Snowcem)
12. Hydrophobic Cement
13. Masonry Cement
14. Expanding Cement
15. Rediset Cement
16. High Alumina cement
110. Ordinary Portland Cement (OPC)
Grades
• 33 Grade min 33 N/mm2 strength (M20)
• 43 Grade min 43 N/mm2 strength (Normal RCC works)
• 53 Grade min 53 N/mm2 strength
For > M30
Can reduce cement by 10 – 15 %
Can reduce steel by 5 – 8 %
High rise buildings, chimney, etc
1
111. Rapid Hardening Cement
• Speedly (rapidly) attains strength (3 days)
• Initial and final setting time same as OPC
• Higher C3S and lower C2S content
early stage strength
(56 %)
• pre-fabricated concrete construction
• Road repair works
• Where speed of construction is needed
Progressive strength
2
112. Extra Rapid Hardening Cement
• RHC + Calcium chloride
• Transported, placed, compacted & finished within about 20 minutes
• Accelerates the setting and hardening process
• Strength 25 % higher than RHC
Uses
• Concreting in cold weather
3
113. Sulphate Resisting Cement
• Resistant to sulphate attack
• low C3A content (below 5 % only)
• Has high silicate content High sulphate resisting ability
Uses
• Sewage treatment works, marine structures
4
114. Portland Slag Cement
• OPC + Granulated blast furnace slag
• Low heat of hydration
• Resistance to chemical attacks
• Resistance to corrosion of steel reinforcement
Uses
• RCC
5
115. Quick Setting Cement
• Sets fastly
• Alumnina ↑
• Gypsum ↓
• Initial setting time = 5 minutes
• Final setting time = 30 minutes
Uses
• Pumping Concrete works
6
116. Super Sulphated Cement
• Granulated slag + gypsum + 5 % Portland cement clinker
• Low heat of hydration
• High sulphate resistance
Uses
• Marine works
7
117. Low Heat Cement
Uses
• Dams, mass concrete works
8
• Opposite of high alumina cement
• Less heat is produced at time of hydration
• Low C3S , C3A reduced
• Slow rate of gain of strength
• Same ultimate strength of OPC
• Initial setting time = 1 hour
• Final setting time = 10 hour
118. Portland Pozzolana Cement (PPC)
• OPC clinker + 10 - 35 % pozzolanic material
• Clinker replaced by cheaper pozzolanic material (Fly ash or Calcined clay)
• PPC gives more volume of mortar than OPC.
• Longer setting times
• Sulphate resistant
• Less compressive strength at early stages
Uses
• Sewage works, under water works, normal works
9
119. Hydrophobic Cement
• Afraid of water !!
• Reduces wetting ability of cement
• Helps to reduce w/c ratio
• Contains admixtures – Acidol
- Napthene soap
- Oxidized petrolatum
• frost and water resistance
10
120. Acid resistant cement11
• Binding material : Soluble gas
• Do not resist water
To resist water add
0.5 % linseed oil or
2 % ceresit
122. High Alumina cement14
Alumina ↑ – 32 % - Quick setting
Initial setting time = 3
𝟏
𝟐
𝐡𝐨𝐮𝐫𝐬
Final setting time = 5 hours
Less time, more strength
In England Cement Fondu
In America Lumnite
By fusing Lime stone + Bauxite, Gypsum not added
123. Properties of cement
• Binder material (adhesive and cohesive property)
• On adding water Hydration (Exothermic reaction-Heat)
• Fineness < 10 % of its original weight
• Initial setting time of OPC = 30 min
• Final setting time of OPC = 600 min
• Specific gravity of OPC = 3.15
• Normal consistency for OPC ranges from 26 to 33%
124. Tests on cement
Field tests Laboratory tests
1. Fineness
2. Specific gravity
3. Consistency
4. Setting time
5. Soundness
6. Compressive strength
7. Tensile strength
125. Field testing of cement
1. Open the bag and take a good look at the cement
- no visible lumps.
2. Colour = Greenish grey
3. Should get a cool feeling when thrusted
4. When we throw the cement on a bucket full of
water, before it sinks the particle should flow
126. 1
Degree to which the cement is grinded
into smaller and smaller particles
Fineness Test on Cement
Using 90 micron IS Sieve
Air permeability method
127. Apparatus required:
IS Sieve 90 micron weighing balancecement
Hydration of cement
During mixing of cement with water, chemical
reaction take place between them. Heat is liberated.
128. 1.Break down any air-set lumps in the cement
sample with fingers.
2.Weigh 100 grams of cement in IS 90 micron
3.Continuously sieve the sample for 15 minutes
4.Weigh the residue left after 15 minutes of sieving.
5.This completes the test.
Procedure
129. Fineness =
𝑨
𝑩
x 100
A = Weight of cement retained on 90 micron IS sieve
(15 minutes)
B = Total weight of sample
Rule in this experiment
For ordinary Portland cement (OPC) fineness should not be more
than 10 % of original weight as per IS code.
130. weight of a given volume of the cement
weight of equal volume of water
Standard value: 3.15
Gc =
2 Specific gravity of cement
132. w1 = weight of empty bottle
w2 = weight of bottle + cement
w3 = weight of bottle + cement + kerosene
w4 = weight of bottle + kerosene full
w5 = weight of bottle + water
w1 w2 w3 w4 w5
133. Gk =
weight of kerosene
𝑤𝑒𝑖𝑔ℎ𝑡 𝑜𝑓 𝑤𝑎𝑡𝑒𝑟
=
Specific gravity of the kerosene
w4 − 𝑤1
𝑤5 − 𝑤1
Specific gravity of the cement
Gc =
𝐰𝐞𝐢𝐠𝐡𝐭 𝐨𝐟 𝒄𝒆𝒎𝒆𝒏𝒕
𝒘𝒆𝒊𝒈𝒉𝒕 𝒐𝒇 𝒂𝒏 𝒆𝒒𝒖𝒂𝒍 𝒗𝒐𝒍𝒖𝒎𝒆 𝒐𝒇 𝒌𝒆𝒓𝒐𝒔𝒆𝒏𝒆
Gc =
𝐰 𝟐
−𝒘 𝟏
𝒘 𝟒
−𝒘 𝟏
−(𝒘 𝟑
−𝒘 𝟐
)
x Gk
134. Standard/Normal Consistency
Initial Setting time
Final Setting time
Standard Plunger (10 mm dia, 50 mm long)
Square needle (1 mm)
Needle with annular collarVicat Apparatus
135. Relative mobility of a freshly
mixed cement paste
Ability of cement to flow.
Easiness of work with cement
3 Standard consistency of cement
139. 400 g cement 25 % water by
weight of dry cement
+
Generally normal consistency for
OPC ranges from 26 to 33%.
Cement paste
Repeat the process till the standard consistency
(Water % for 33-35 mm penetration from top) is got
Gauging time
( 3-5 minutes)
140. 1. Take 400 g cement
2. Add 25 % water by weight of dry cement
3. Prepare cement paste within 3-5 minutes (Gauging time)
4. Fill in Vicat mould
5. Attach standard plunger above the test block
6. Release plunger and note depth of penetration
7. If penetration ranges from 33-35 mm from top, it is standard
consistency for given cement.
8. Else add 1 % more water and repeat the experiment till we get
standard consistency.
Procedure
141. The time elapsed between the moment water is added to
the cement to the time at which cement paste starts
losing its plasticity.
Initial setting time:
For OPC > 30 minutes
4 Initial and final setting time
142. The period elapsing between the time water is added to
the cement and the time the needle makes an impression
on the surface of the test block
Final setting time:
For OPC < 10 hours or 600 minutes
143. 1. Take 300 g cement
2. Add 0.85 times water required for standard consistency
3. Start stop watch
4. Prepare cement paste within 3-5 minutes (Gauging time)
5. Fill in Vicat mould
6. Attach square needle above the test block
7. Release square needle. In beginning needle penetrates completely.
8. Paste starts losing its plasticity.
9. Release after half an hour, the needle penetrates 33-35 mm from top.
Stop watch and note the time (initial setting time).
10.Replace needle with annular collar needle. Check after 10 hours.
11.Note the no impression forming time (final setting time).
Procedure
144. • Reason: insufficiency in grinding, burning, etc
• Soundness = Ability of hardened cement paste to
retain its volume after setting without expansion.
Cement does not undergo any large expansion
• Ensures:
To detect the presence of excess lime in
cement
5 Soundness test
145. • Le Chatelier test detects unsoundness due to free lime only
• If expansion of cement > 10 mm
• Unsound
• Excess lime Cracks
• Expansion should be less than 10 mm
• OPC – Ordinary Portland Cement
• RHC – Rapid Hardening Cement
• Low Heat Portland Cement
146. Take a
sample of
100
grams
cement.
Paste
0.78 x P
Cover
with
glass
sheet
Fill in Le chatelier apparatus
Immerse in water, 24 hrs, 270C
Note the distance b/w pointers
before boiling – d1
Boil 3 hrs – reach boiling
point within 25-30 minutes
Note the
distance b/w
pointers after
boiling – d2
Cool
Expansion = d2 – d1
149. Uses of cement
Mortar for plastering
Masonry works
Pointing works
Floors, roof, beam, column, footing, lintel, etc
For construction of engineering structures
For making concrete for various structures
Crack filling
150.
151. Pozzolana
A natural siliceous and aluminous material
Pozzolana + Calcium Hydroxide Pozzolanic reaction
Have binding/cementitious property
Formed from volcanic ash/other means
Portland cement contains pozzolanas
Eg:- Surkhi, blast furnace Slag, Rice husk ash
152. Common puzzolonas used as admixtures in cement
1. Surkhi
2. Blast furnace Slag
3. Fly ash
4. Silica Fume
5. Rice- husk Ash
- Brick dust
- Waste of iron manufacturing
- Burning of coal
- Byproduct of silicon
154. Sand
• Sand basically consists of Silica (SiO2)
• Formed by decomposition of sandstone due to weathering action.
Types/sources of Sand
1. Pit sand - angular shape
2. River sand – round shape
3. Sea sand – from sea shore. Contain salts.
4. Sand dunes – desert sand
• Also called as adulterant
155. Classification of sand
1. Fine sand < 1.5875 mm
2. Coarse sand < 3.175 mm
3. Gravelly sand < 7.62 mm
156. Limitations of mining of sand from
rivers and sea shore
• Disturbs natural equilibrium
• Problems to bridges
• Problems to fishes and river inhabitants
• Contamination of river water
• Affects quality of river water
158. M-sand
• Manufactured sand
• Alternative to river sand
• Cost of construction is less
• Low water absorption
• Manufactured by crushing of rocks
• In reality, better than river sand.
159. Coarse aggregates
• Size > 4.75 mm
• Major contribution to strength in concrete
• Influences workability & degree of compaction of concrete
• Materials generally used are :
1. Gravel
2. Crushed stone
3. Slag
4. Recycled concrete
5. Geo-synthetic aggregates
160. Requirements of good coarse aggregates
• Hard, strong and durable
• Free from organic impurities
• Free from grass and roots
• Clay content < 4 %
• Resistance to change in volume
• Well graded
161. Commonly used sizes for different applications
• Roads = 40 mm
• Column and slab = 20 mm
• Self compacting concrete (SCC) = 10 mm
• Retaining walls and abutments = 75 mm
• Concrete dams = 75 mm
Different based on type of work. Commonly used are
162. Grading of coarse and fine aggregate
• Particle size distribution of aggregates
• Measured by sieve analysis method
• Described using Grading curve
Gives ‘cumulative % passing’
against standard IS Sieves
• Influences workability & degree of compaction
163. • Poorly graded All particles of aggregate
have same size – more voids
• Well graded Contains particles of all sizes (GOOD)
• Gap graded Some big, some small particles.
164. Mortar (Matrix)
• Composite mixture
• Cement + Sand + water (No coarse aggregate)
• Used in plasterings, masonry, etc
Concrete
• Composite mixture
• Easily mouldable
• Cement + Sand + Coarse aggregate + water
• Used in beams, columns, slabs, footings, stairs, etc
165. Functions of sand in mortar
1. Void filler
2. Bulking – Sand bulks volume of mortar increases Thus cost reduced.
3. Setting – setting of fat lime occurs effectively due to sand
4. Shrinkage – sand prevents excessive shrinkage of mortar & prevent cracking
5. Strength – helps in adjustment of strength by varying its proportion.
166. Preparation of lime mortar
Prepared by grinding or pounding
1 - Grinding – for large quantities of lime mortar
2 - Pounding – for preparing small quantities
167. Preparation of cement mortar
Does not require grinding or pounding
Cement and sand are mixed in required proportions in
dry state on a watertight platform
Add water and mix thoroughly
168. Proportions of mortar for various items of work
No Nature of work Mortar proportion
1 Construction work in waterlogged areas and exposed positions 1:3
2 Damp proof courses and cement concrete roads 1:2
3 General RCC work such as lintels, pillars, slabs, stairs etc 1:3
4 Internal walls 1:3
5 Partition walls and parapet walls CM 1:3 or LM 1:1.
6 Plaster work (finishing mortar) 1:3 to 1:4
7 Pointing work 1:1 to 1:2
8 Brick laying mortar 1:6 to 1:8
170. 1. Adhesiveness to building units
1. Place two bricks at right angles
2. If size of brick is 19 x 9 x 9 cm brick, a
horizontal joint 9 cm x 9 cm = 81 cm2 is formed
3. The upper brick is suspended from an overhead
support and weights are attached to lower brick
4. Weights are gradually increased till separation
of brick occurs
Ultimate adhesive strength = Maximum load
81
171. 2. Crushing strength
1. Prepare a brickwork with mortar
2. Apply gradual load to this sample brickwork till failure occurs
by crushing.
Ultimate Crushing strength = Maximum load .
Cross sectional area
172. 3. Tensile strength
1. Mortar is placed in briquette mould
2. Briquettes are tested in a tension
testing machine
175. Proportioning/Batching concrete
Process of selection of relative proportions of
cement, sand, coarse aggregate and water so as to
obtain a concrete of desired quality.
Process of measuring concrete mix ingredients either
by mass or volume and introducing them into the
mixer.
176. Types of Proportioning
1. Volume batching
2. Weight batching
• Small jobs
• Accurate and uniform proportioning
177. PCC and RCC
PCC – Plain Cement Concrete – no rebars
RCC – Reinforced Cement Concrete
Structural concrete
• Concrete + steel bars
• Tensile strength of concrete = 7–15 % of compressive strength
178. Functions of water in concrete:
• Potable water (drinking water can be used) is used in concrete.
• Water makes the concrete workable
• Amount of water controls Hydration
• Amount of water controls Curing
• Defines strength of concrete
• Defines shrinkage of concrete
Water lubricates aggregates and facilitates passage of cement through voids.
179. Water-cement ratio
Amount of water
Amount of cement by weight
w/c ratio =
• Ratio of weight of ‘free water’ (excluding that absorbed
by aggregates) to cement in a mix.
• Strength and quality of cement concrete primarily
depends on w/c ratio
• Strength and quality of cement concrete primarily
depends on w/c ratio
180. Abrams Law
Water-cement ratio is inversely proportional to compressive
strength of concrete.
Low w/c ratio is good
181. Advantages of low w/c ratio
• Increases compressive strength
• Lower permeability
• Increased resistance to weathering
• Better bond b/w concrete and reinforcement
• Reduce shrinkage and cracking
182. Advantages of low w/c ratio
• Increases compressive strength
• Lower permeability
• Increased resistance to weathering
• Better bond b/w concrete and reinforcement
• Reduce shrinkage and cracking
183. Characteristics of concrete
Unit weight = 25 kN/m3
Compressive strength Eg:- M20, MMix, 20 fck = 20 MPa
Increase in strength with age
Tensile strength of concrete Flexural strength, fcr = 0.7 √fck N/mm2
Elastic Deformation Ec = 5000 √fck N/mm2
Shrinkage of concrete Strain = 0.0003
Creep of concrete
Thermal expansion of concrete
184. Characteristics of reinforcement
Unit weight = 7850 kg/m3
Modulus of Elasticity, E = 2 x 105 N/mm2
Poisson ratio, 𝝁 = 𝟎. 𝟑
Should bond well with concrete
Should have good strength
Should have good ductility
Should have good resistance against corrosion
185. Concrete grade and mix ratio
Mix Mix ratio Nature of work
M 5.0 1:5:10 Mass concrete for heavy walls,
footings, etc
M 7.5 1:4:8 Mass concrete – foundations of
less importance
M 10 1:3:6 Mass concrete – foundations of
less importance
M 15 1:2:4 General RCC works (Slab, beam,
column, etc)
M 20 1:1.5:3 Water retaining structures, piles,
and general RCC works
M 25 1:1:2 Heavy loaded RCC structure –
long span slabs, beams, etc
186. Workability
Property of freshly mixed concrete (or mortar) which
determines the ease and homogeneity with which it
can be mixed, placed, compacted and finished.
Ability to flow and work with concrete
187. Factors affecting workability
• Water content
• Size – finer particles more water large specific surface
• Texture and grading
• Shape – Angular aggregates require more water than rounded aggrgates
• Mix proportions
• Grading of aggregates
• Use of admixtuers
189. • Field and lab test to find workability of fresh concrete
Slump test
190. Slump
The difference in height between the concrete before
removing slump cone and height of the concrete after
removing of slump cone
191. Types of slump
1. Zero slump – no slump when slump cone is removed
2. Collapse slump
3. Shear slump – some portion subsides largely
4. True slump
192. 1. Prepare mix and fill slump cone in 3 layers – 25 times
tamping to each layer
2. Cut the excess concrete and level the top
3. Remove the slump cone slowly
4. Measure the slump : Max slump = 300 mm
Procedure for slump test
193. • Field and lab test
Compaction factor test
Prepare mix. Eg: M20
A
B
194. • Fill concrete in HOPPER A
• Open trap door Concrete falls to HOPPER B
• Open trap door Concrete falls to CYLINDER
• Note the weight of partially compacted concrete
• Remove all concrete from cylinder – EMPTY IT
• Again fill the cylinder from same sample mix
• 3 LAYERS – 25 Tamping with tamping rod
• Weight the fully compacted concrete
• Compaction Factor is
C.F =
𝐖𝐞𝐢𝐠𝐡𝐭 𝐨𝐟 𝐩𝐚𝐫𝐭𝐢𝐚𝐥𝐥𝐲 𝐜𝐨𝐦𝐩𝐚𝐜𝐭𝐞𝐝 𝐜𝐨𝐧𝐜𝐫𝐞𝐭𝐞
𝐖𝐞𝐢𝐠𝐡𝐭 𝐨𝐟 𝐟𝐮𝐥𝐥𝐲 𝐜𝐨𝐦𝐩𝐚𝐜𝐭𝐞𝐝 𝐜𝐨𝐧𝐜𝐫𝐞𝐭𝐞
Procedure for compaction factor test
195. Reinforced Cement Concrete (RCC)
• Concrete is good in resisting compression, but
weak in taking tension.
• So reinforced bars provided where tension occurs
• Cement + Sand + Coarse aggregate + water + rebars
• Used in beams, columns, slabs, footings, stairs, etc
• Concrete take compression and rebars takes tension
196. Qualities of reinforcing material
• Easily available in bulk and economical
• High tensile stress and elasticity
• Good durability
• Should be corrosion resistant
• Good bonding with concrete
• Thermal coefficient of expansion should be
nearly equal to that of concrete to minimise
thermal stress
197. Steel and types
Steel
Mild steel Fe 250
HYSD bars
Fe 415, Fe 415 D
Fe 500, Fe 500 D
Fe 600
TMT
Thermo Mechanically
TreatedHigh Strength Steel
198. Types of reinforcement used
1. Hot Rolled Deformed Steel Bars
2. Cold Worked Steel Bars
3. Mild Steel Plain Bars
4. Prestressing Steel Bars
199. 1. Hot Rolled Deformed Steel Bars
Mostly used for RCC structures
Certain ribs (deformations) on steel surface
These ribs helps to develop good bond with concrete
200. 2. Cold Worked Steel Bars
Bars undergo twisting and drawing in cold working process
3. Mild Steel Plain Bars
Do not have ribs on their surface – plain surface
Used for small projects - economical
201. 4. Prestressing Steel Bars
In form of tendons
Cold formed and have a high tensile strength
202. Tests on Hardened concrete
1. Compression test (cube & cylinder)
2. Flexural strength test
3. Split tensile strength test
203. Compression test - cube
• 3 cubes – 15 X 15 X 15 cm
• Mould removal – after 1 day
• Curing – 3, 7, 28 days
• Tested using UTM/CTM
207. Chemical admixtures
1. Plasticizer
2. Superplasticizer
3. Accelerators
4. Retarders
5. Air entraining admixtures
6. Water-reducers
Chemicals added to concrete before or during
mixing of concrete to modify some specific
property of fresh or hardened concrete.
Eg:-
208. Plasticizers and super plasticizers
• A type of water reducing admixture
• Also called as High range water reducer
• Increased fluidity : flowing, self levelling, etc
• Reduced water cement ratio: High early strength
• Commonly used superplasticizers are
1. Sulphonated melamine formaldehyde condensates (SMF)
2. Sulphonated naphthalene formaldehyde condensates (SNF)
3. Polycarboxylate ether superplasticizers (PCE)
209. • A type of admixture
• Increase rate of hydration of cement
• Reduce setting time
• Increase rate of strength development
• Eg:- Na2SO4, NaCl, K2SO4, CaCl2
Accelerators
210. • To increase (retard/delay) the setting time
• Slow rate of hydration
• Helpful – concrete transporting to long distance
• Eg:- Derivatives of sugar and carbohydrates,
gypsum, plaster of paris, etc
Retarders
212. Timber
Timbrian = build
Timber means wood suitable for building /
carpentry / engineering purposes
Standing timber
Rough timber
Converted timber
Timber contained in a living tree
Obtained after felling a tree
Timber sawn & cut into suitable commercial sizes
213. Classification of trees
Exogenous Endogenous
(Grow outwards) (Grow inwards and longer)
Conifers Deciduous
Used for engg
purposes
Eg: - Bamboo, cane,
palm, coconut tree
Ever green trees
Leaves do not fall till new
ones grows
Bears cone shaped fruits
Eg: Mango tree
Soft wood
Broad-leaf trees
Leaves fall in autumn and
new ones appear in spring
Mostly for engg purposes
Eg: Teak
Hard wood
214. Soft wood | Hard wood
• Ever green trees
• Distinct annual rings
• Light colour
• Poor fire resistance
• Indistinct medullary rays
• Can split easily
• Light weight
• Broad-leaf trees
• Indistinct annual rings
• Dark colour
• More fire resistance
• Distinct medullary rays
• Can’t split easily
• Heavy weight
215. Structure of a tree
1. Micro structure
2. Macro structure
Timber studied under microscope
Timber studied with naked eye
216. Micro structure
Timber consists of living and dead cells
Living cells – membrane, protoplasm, sap, core
1. Conductive cells
Transfer nutrients from roots to various parts of tree
2. Mechanical cells
Tightly interconnects cells and imparts strength to tree
3. Storage cells
Extra nutrients are stored
218. Pith (core/medulla)
Heart wood
Sap wood (Albernum)
Innermost central portion
Inner annular rings surrounding pith
Usually dark in colour
Used for engineering purposes
Outer annular rings b/w heart wood and cambium layer
Light weight and light colour
It take active part in growth of tree
Supply nutrients at young age
219. Cambium layer
Thin layer of sap b/w sap wood
and inner bark
This get converted into sap wood
Inner bark
Inner layer covering (protection to) cambium layer
Outer bark (Cortex)
Outermost protective layer of a tree
Medullary rays
Thin radial layers extending from pith to cambium layer
Hold together annual rings of heart wood & sap wood.
220. Defects in timber
Conversion Fungus Natural forces Insects Seasoning
1. Chip mark
2. Diagonal grain
3. Torn grain
4. Wane
1. Blue stain
2. Sap stain
3. Dry rot
4. Wet rot
5. Brown rot
6. White rot
7. Heart rot
1. Burls
2. Callus
3. Chemical stain
4. Coarse grains
5. Dead wood
6. Druxiness
7. Foxiness
8. Knot
9. Rind gall
10.Shake
1. Cup shake
2. Ring shake
3. Heart shake
4. Star shake
5. Radial shake
11.Twisted Fibre
12.Upset or rupture
13.Water stain
14.Wind crack
1. Beetles
2. Marine borers
3. Termites
1. Check
2. Split
3. Cup
4. Bow
5. Twist
6. Warp
7. Collapse
8. Case hardening
9. Radial shake
10.Honey combing
due to
221. 1. Defects due to conversion
Marks/signs placed by chips on finished timber surface
1. Chip mark
May be formed by parts of planing machine, chisel marks, etc
Due to improper sawing of timber
2. Diagonal grain
Affects appearence
Not affects strength
Should cut parallel to layers/fibers
Don’t cross fibers while cutting
222. When heavy equipments falls on a finished surface,
depressions are formed.
3. Torn grain
Due to improper sawing of timber
4. Wane
Not affect strength, but affect appearence
223. 2. Defects due to fungus
Fungus attacks timber if
(i) moisture content > 20 % and
(ii) in presence of air.
Wood submerged in water will not affected by fungus
Wood having moisture content < 20 % will not affected
by fungus
224. 3. Dry rot
Certain fungus attack timber and convert it into powder form
4. Wet rot
Some fungus causes chemical decomposition of wood
that convert timber into greyish brown powder.
1. Blue stain
Sap of wood is stained to bluish colour by action of fungi
2. Sap stain
Sap wood losses its colour due to fungus attack.
225. 5. Brown rot
Rot means decay/disease of timber
Some fungus attacks cellulose White colour losses.
Thus brown colour of lignin dominates and wood seen
as brown colour.
6. White rot
Some fungus attacks lignin Brown colour losses.
Thus white colour of cellulose dominates and wood seen
as white colour.
226. 7. Heart rot
Formed when branches are cut
Heart wood is exposed to attacks of atmospheric agents
Tree becomes weak; it gives us hollow sound when
stuck with a hammer.
Fungus develops holes in timber
227. 3. Defects due to natural forces
1. Burls
When tree gets shock/injury in its young age
Also known as excrescences
Due to such injury, growth of tree becomes completely
upset and irregular projections appear on the body of
timber.
2. Callus
Soft tissue or skin which covers the wound of a tree
228. 3. Chemical stain
Wood sometimes discoloured by chemical actions.
4. Coase grain
If a tree grows rapidly, annual rings are widened.
Have less strength
5. Dead wood
Timber obtained from dead standing trees
229. 6. Druxiness
White decayed spots concealed by healthy wood
7. Foxiness
Red or yellow tinge in wood
Due to
(i) Bad ventilation
(ii) Over maturity
230. 8. Knot
Bases of cut-off branches of a tree
Continuity of wood fibre is lost due to knots Weak
Dark and strong (even saw breaks)
Losses alignment of fibers
231. 9. Rind galls
Rind means bark; gall means abnormal growth
Develops at points from where branches are
improperly cut-off.
Nutrients get still supplied at that points
Fibers gets cutted
232. 10. Shakes
Cracks formed in annual ring direction
a) Cup shakes
Curved cracks
Seperates partly one
annual ring from other
233. Shake
Cup shake
Ring shake
Heart shake
Radial shake
Star shake
10. Shakes
When cup shakes cover entire annual rings
b) Ring shakes
234. 10. Shakes
Cracks formed at centre of cross-section
c) Heart shakes
Extends from pith to sapwood in
direction of medullary rays.
Due to maturity, inside starts shrinking
Divides tree into two or four parts
235. 10. Shakes
Cracks from bark towards sapwood.
d) Star shakes
Cracks upto sap only
Not reach heartwood or pith
Can remove outer area and use
Due to extreme heat or frost
236. 10. Shakes
Similar to star shakes
d) Radial shakes
Outer surface easily dries
Shrinks from outer to inner
But they are fine, irregular and numerous
Extends from bark towards center
237. 11. Twisted fibre
Also known as wandering hearts
Due to twisting of young trees by fast blowing wind
While sawing, it cuts fibers everywhere. Means it cannot
used by cutting. But can use as a single wood.
238. 12. Upset
Also known as rupture
Wood fibers injured by compression
Due to improper felling of trees
13. Water stain
Wood sometimes discolours when it
comes in contact with water
14. Wind cracks
If wood exposed to atmospheric agencies,
its exterior surface shrinks cracks
239. 4. Defects due to insects
3. Termites
White ants
1. Beetles
Creates holes in wood for food fine flour like powder
2. Marine borers
Salty waters make holes in timber for shelter
240. 5. Defects due to seasoning
1. Check
Crack which seperates fibers of wood
Does not extend from one end to other
242. 3. Cup
Curvature formed in transverse direction
4. Bow
Curvature formed in direction of length of timber
243. 5. Twist
When a piece of timber get spirally distorted along
its length
6. Warp
When a piece of timber has twisted out of shape
244. 1. Check
2. Split
3. Cup
4. Bow
5. Twist
6. Warp
7. Collapse
8. Case hardening
9. Radial shake
10.Honey combing
7. Collapse
Due to uneven shrinkage, wood sometimes
flattens during drying.
8. Case hardening
Exposed surface of timber dries rapidly
Under Compression
Interior surface not completely dried
Under tension
245. 9. Radial shake
10. Honey combing
Due to stresses developed during drying, various
radial and circular cracks develop in the interior
portion of timber.
246. Seasoning of timber
Newly felled tree contains > 50 % water in form of sap
To use timber for engineering purposes, water should be
removed. (Timber should be dried)
Process of drying of timber to remove water is known as
seasoning.
Water is in the form of sap and moisture
247. Allows timber to burn rapidly, if used as fuel
To improve strength, hardness, stiffness, and
electrical resistance properties
To reduce tendency of timber to crack, shrink and warp.
To make the timber safe from attacks of insects and fungus.
To make the timber fit for uses for engineering purposes
Objects of Seasoning
Improves workability of timber
Reduces much of useless weight of timber
248. Methods of seasoning
Natural Seasoning Artificial Seasoning
When seasoning of timber
is carried out by natural air
or water.
249. Natural Seasoning
1. Water seasoning 2. Air seasoning
Timber is immersed in water
flow which helps to remove
the sap present in the timber
Allow timber to dry for
2 to 4 weeks
Arrange timber logs in layers
in a shed.
Air is circulated freely
between logs moisture
reduces
Slow process, but we get
well seasoned timber
250. Artificial Seasoning
1. Boiling
Timber allowed to
dry after boiling for
3 to 4 hours
2. Chemical
Timber stored in
salt solution. Salt
absorb water.
3. Kiln
Timber stored in
salt solution. Salt
absorb water.
4. Electrical
timber subjected
to high frequency
AC currents
251. Carried out to increase the life of timber
Preservation of timber
Preserve timber from decaying
To increase durability, to get rid of insects and fungi, etc.
Application of chemical substance on timber surface
Presevatives makes timber ‘poisonous’ for insects and fungi
without affecting the structural properties of timber.
252. Methods of Timber Preservation
Brushing
Spraying
Injecting under pressure
Dipping and stepping
Charring
Hot and cold open tank treatment
253. Types of preservatives for timber
Coal tar – heat and apply using brush
ASCU – powder dissolved in water and apply by spraying
Chemical salts – CuSO4, ZnCl
Oil paints
Solignum paints – applied using brush
Creosote oil
254. Wood products
Industrial timber
– timber prepared scientifically in a factory
– examples are :
Veneer
Plywood
Fibreboard
Impreg timber
Compreg timber
255. 1. Veneer
Thin sheets of wood of superior quality
Thickness = 0.4 mm to 6 mm
Obtained by rotating a log of wood against a
shark knife of rotary cutter
Dried in kilns to remove moisture
256. Process of preparing a sheet of veneer is
known as veneering.
Veneers are used to produce plywood's,
batten boards, and laminboards.
Glued on the surface of inferior wood to
create an impression that whole piece is
made of expensive timber
257. 2. Plywoods
Ply means thin layer
Veneers placed in both longitudinal and transverse
directions more strength
Suitable adhesives are used to held in position
Available in different commercial sizes
258. Used for:
1. Ceilings
2. Doors
3. Furniture
4. Partitions
5. Paneling walls
6. Formworks of concrete
266. Crude impure iron extracted from iron ores
Parent metal of cast iron, wrought iron & steel
5 – 6 % Carbon content
Pig iron
Manufactured in blast furnace
267. Cannot magnetized
Cannot welded or rivetted
Does not rust
Difficult to bend
Hard and brittle
Neither ductile nor malleable
High compressive strength
Properties of pig iron
268. Pig iron
Cast iron Wrought iron Steel
2 – 4 % carbon content
Made in cupola furnace
Cannot magnetized
Good compressive
strength
Will not rust easily
Not ductile and malleable
Uses: water pipes, sewers,
gates, lamp posts,castings,
compression members, rail
chairs, carriage wheels
Re-melting with
coke and lime
Almost pure iron
Less than 0.15 % C
Reverberatory furnace
Good tensile strength
Temporary magnetization
possible
Ductile, Malleable, fibrous
Fuses with difficulty (1500oC)
Uses: Rivets, chains, nuts
and bolts, railway couplings,
handrails
C = 0.25 – 1.5 %
Bessemer process
Permanent magnets
Mechanical treatments
possible: forging,
drawing, pressing, rolling
Malleable and ductile
Types and uses:
269.
270. Good conductor of heat and electricity
Highly resistant to corrosion
High temperature resistant
Light weight and takes more load
Specific gravity = 2.7
Possess great toughness and tensile strength
Ore: Bauxite (Al2O3.2H2O)
1. Aluminum
It readily dissolves in Hydrochloric acid
271. Utensils
Corrugated roofing sheets
Structural members
Electric wires
Window frames
For making parts of aeroplane
Uses of Aluminum
Possess great toughness and tensile strength
It readily dissolves in Hydrochloric acid
272. Cannot welded
It has a peculiar red colour
Ores:
Cuprite
Copper glance
Copper pyrites
Malachite
Azarite
2. Copper
Good conductor of heat and electricity
273. Specific gravity = 8.90
Malleable, ductile and soft
Not attacked by water at any temperature,
But attacked by steam at white heat.
Household utensils
Electroplating
Wires and electric cables
Uses of Copper
274. Specific gravity = 11.36
It can be cut with knife
It is lustrous metal with bluish grey colour
It is soft
Ore: Galena
3. Lead
Uses: Shot puts, bullets, base in paints,
storage cells
275. Not occur in free state in nature
It is a bluish white metal
It is not affected by dry air and water
It is brittle at ordinary temperature
Ore: Zincite, Franklinite, Calamine, Zinc Blende
4. Zinc
Uses: Paint, electric cells, Galvanising
276. Similar strength as steel & weight nearly half of steel
Have high melting point
Good corrosion resistance
Not found in free state
Stronger than aluminum
5. Titanium
Uses: Aerospace, marine, chemical and
biomedical applicatios – turbine blades, bone
screws, dental fixtures, surgical instruments
Editor's Notes
Engineering structures are composed of materials.
Component minerals of granite are felspar, mica and quartz
Slate used as roofing
Granite takes polish very well
Colour of granite is grey, green or brown