footing

Definition Footings are structural members used to support columns and walls and to transmit and distribute their loads to the soil in such a way that the load bearing capacity of the soil is not exceeded, excessive settlement, differential settlement,or rotation are prevented and adequate safety against overturning or sliding is maintained.

Wall footings are used to support structural walls that carry loads for other floors or to support nonstructural walls.

Isolated or single footings are used to support single columns. This is one of the most economical types of footings and is used when columns are spaced at relatively long distances.

Combined footings usually support two columns, or three columns not in a row. Combined footings are used when tow columns are so close that single footings cannot be used or when one column is located at or near a property line.

Cantilever or strap footings consist of two single footings connected with a beam or a strap and support two single columns. This type replaces a combined footing and is more economical.

Continuous footings support a row of three or more columns. They have limited width and continue under all columns.

Rafted or mat foundation consists of one footing usually placed under the entire building area. They are used, when soil bearing capacity is low, column loads are heavy single footings cannot be used, piles are not used and differential settlement must be reduced.

Pile caps are thick slabs used to tie a group of piles together to support and transmit column loads to the piles.

When the column load P is applied on the centroid of the footing, a uniform pressure is assumed to develop on the soil surface below the footing area. However the actual distribution of the soil is not uniform, but depends on may factors especially the composition of the soil and degree of flexibility of the footing.

Soil pressure distribution in cohesionless soil. Soil pressure distribution in cohesive soil.

Footings must be designed to carry the column loads and transmit them to the soil safely while satisfying code limitations. The area of the footing based on the allowable bearing soil capacity Two-way shear or punching shear. One-way bearing Bending moment and steel reinforcement required * * * *

Footings must be designed to carry the column loads and transmit them to the soil safely while satisfying code limitations. Bearing capacity of columns at their base Dowel requirements Development length of bars Differential settlement * * * *

The area of footing can be determined from the actual external loads such that the allowable soil pressure is not exceeded. Strength design requirements

For two-way shear in slabs (& footings) V c is smallest of long side/short side of column concentrated load or reaction area<2 length of critical perimeter around the column where,  c = b 0 = ACI 11-35 When  >2 the allowable V c is reduced.

Assume d. Determine b 0 : b 0 = 4(c+d) for square columns where one side = c b 0 = 2(c 1 +d) +2(c 2 +d) for rectangular columns of sides c 1 and c 2 . 1 2

The shear force V u acts at a section that has a length b 0 = 4(c+d) or 2(c 1 +d) +2(c 2 +d) and a depth d; the section is subjected to a vertical downward load P u and vertical upward pressure q u . 3

Allowable Let V u =  V c 4 If d is not close to the assumed d, revise your assumptions

For footings with bending action in one direction the critical section is located a distance d from face of column

The ultimate shearing force at section m-m can be calculated If no shear reinforcement is to be used, then d can be checked

If no shear reinforcement is to be used, then d can be checked, assuming V u =  V c

The bending moment in each direction of the footing must be checked and the appropriate reinforcement must be provided.

Another approach is to calculated R u = M u / bd 2 and determine the steel percentage required  . Determine A s then check if assumed a is close to calculated a

The minimum steel percentage required in flexural members is 200/f y with minimum area and maximum spacing of steel bars in the direction of bending shall be as required for shrinkage temperature reinforcement.

The reinforcement in one-way footings and two-way footings must be distributed across the entire width of the footing. where

The loads from the column act on the footing at the base of the column, on an area equal to area of the column cross-section. Compressive forces are transferred to the footing directly by bearing on the concrete. Tensile forces must be resisted by reinforcement, neglecting any contribution by concrete.

Force acting on the concrete at the base of the column must not exceed the bearing strength of the concrete where  = 0.7 and A 1 =bearing area of column

The value of the bearing strength may be multiplied by a factor for bearing on footing when the supporting surface is wider on all sides than the loaded area. The modified bearing strength

A minimum steel ratio  = 0.005 of the column section as compared to  = 0.01 as minimum reinforcement for the column itself. The number of dowel bars needed is four these may be placed at the four corners of the column. The dowel bars are usually extended into the footing, bent at the ends, and tied to the main footing reinforcement. The dowel diameter shall not =exceed the diameter of the longitudinal bars in the column by more than 0.15 in.

The development length for compression bars was given but not less than Dowel bars must be checked for proper development length.

Footing usually support the following loads Dead loads from the substructure and superstructure Live load resulting from material or occupancy Weight of material used in backfilling Wind loads

A site investigation is required to determine the chemical and physical properties of the soil. Determine the magnitude and distribution of loads form the superstructure. Establish the criteria and the tolerance for the total and differential settlements of the structure. 1 2 3

Determine the most suitable and economic type of foundation. Determine the depth of the footings below the ground level and the method of excavation. Establish the allowable bearing pressure to be used in design. 4 5 6

Determine the pressure distribution beneath the footing based on its width Perform a settlement analysis. 7 8

Design a plain concrete footing to support a 16 in thick concrete wall. The load on the wall consist of 16k/ft dead load (including the self-weight of wall) and a 10 k/ft live load the base of the footing is 4 ft below final grade. f c = 3ksi and the allowable soil pressure = 5k/ft 2

footing

Recommended

Recommended

More Related Content

What's hot

What's hot (20)

Viewers also liked

Viewers also liked (20)

Similar to footing

Similar to footing (20)

More from illpa

More from illpa (20)

footing