Faults in the Knitted Fabrics

Faults in the Knitted Fabrics:
A defect of the knitted fabric is an abnormality which spoils the aesthetics i.e. the
clean & uniform appearance of the fabric & effects the performance parameters,
like; dimensional stability etc.
There are various types of defects which occur in the Knitted fabrics of all types
caused by a variety of reasons. The same type of defects may occur in the fabric
due to a variety of different causes e.g. Drop Stitches, Spirality etc.
Category of Defects:
1. Yarn Related Defects:
Almost all the defects appearing in the horizontal direction in the knitted fabric are
yarn related. These defects are mainly;
Barriness
Thick & Thin lines
Dark or Light horizontal lines (due to the difference in dye pick up)
Imperfections
Contaminations
Snarling
Spirality
2. Knitting Elements Related Defects:
Almost all the defects appearing in the vertical direction in the knitted fabrics are as a cause of bad
Knitting Elements. These defects are mainly;
Needle & Sinker Lines
Drop Stitches etc.

3. Machine Settings Related Defects:
These defects appear randomly in the knitted fabrics due to the wrong knitting
machine settings &that of the machine parts. The defects are mainly;
Drop Stitches
Yarn Streaks
Bariness
Fabric press off
4. Dyeing Related Defects:
The Dyeing related defects are as follows;
Dyeing patches
Softener Marks
Shade variation
Tonal variation
Color fading (Poor Color Fastness)
Dull shade
Crease or rope Marks
Finishing Related Defects:
Defects caused mainly due to the wrong process parameters are;
High Shrinkage
Skewing
Spirality
Surface Hairiness & Pilling
Tonal variation
Snagging (Sharp points in the dyeing machine or trolley etc)
Fold Marks
Wet Squeezer Marks
GSM variation
Fabric Width variation
Curling of S.J. Fabrics

Some common Fault of knitted fabrics are given below
Drop stitches (Holes)
Drop stitches are randomly appearing small or big holes of the, same or different
size, which appear as defects, in the knitted fabrics
Causes:
 High Yarn Tension
 Yarn Overfeed or Underfeed
 High Fabric Take Down Tension
 Defects like Slobs, Naps, and Knots etc.
 Incorrect gap between the Dial & Cylinder rings.
Remedies:
 Ensure uniform yarn tension on all the feeders with a Tension Meter.
 Rate of yarn feed should be strictly regulated as per the required Stitch Length.
 The fabric tube should be just like a fully inflated balloon, not too tight or too slack.
 The yarn being used should have no imperfections like; Slubs, Neps & big knots etc
 The gap between the Cylinder & the Dial should be correctly adjusted as per the knitted
loop size.

Barriness
Barrenness defects appear in the knitted fabric, in the form of horizontal stripes of
uniform or variable width
Causes:
 High Yarn Tension
 Count Variation
 Mixing of the yarn lots
 Package hardness variation
Remedies:
 Ensure uniform Yarn Tension on all the feeders.
 The average Count variation in the lot should not be more than + 0.3
 Ensure that the yarn being used for Knitting is of the same Lot.
 Ensure that the hardness of all the yarn packages is uniform using a hardness tester.

Imperfections
Imperfections appear on the fabric surface, in the form of unevenly placed or
randomly appearing, knots, slobs, & naps, thick & thin places in the yarn.
Causes:
Big Knots, Slubs & Neps in the yarn, Thick & Thin yarn.
Remedies:
Specify the quality parameters of the yarns to be used for production to the yarn supplier.

Spirality
Spirality appears in the form of a twisted garment, after washing. The seams on
both the sides of the garment displace, from their position & appear on the front &
back of the garment.
Causes:
 High T.P.I. of the Hosiery Yarn
 Uneven Fabric tension on the Knitting machine.
 Unequal rate of Fabric feed on the Stenter, Calendar & Compactor machines.
Remedies:
 Use the Hosiery yarns of the recommended TPM level for Knitting.
 Ensure uniform rate of feed of the dyed fabric on both the edges while feeding the fabric
to the Calendar, Compactor or Stenter machines.

Fly
Fly is occurred by flying materials.
Causes:
 Presence of dead fibers & other foreign materials, such as; dyed fibers, husk & synthetic
fibers etc.
 Dead fibers do not pick up color during Dyeing
Remedies:
 Use rich fiber mixing for the yarns, to be used for Knitting, in order to have less dead
fibers, appearing in the fabric.
 Rigid control measures in the Blow Room, to prevent the mixing of foreign matters in the
Cotton mixing

Broken Needle
Defects caused by the broken needles show prominently as vertical lines parallel to
the Wales. There are no loops formed in the Wale which has a broken needle.
Causes:
 High Yarn Tension
 Bad Setting of the Yarn Feeders
 Old & Worn out Needle set
Remedies:
 Ensure uniform & the right Yarn tension on all the feeders.
 Keep the recommended gap, between the Yarn Feeders & the Needles.
 Periodically change the complete set of needles.

Sinker Lines
Sinker lines are prominent or feeble vertical lines appearing parallel to the Wales
along the length of the knitted fabric tube.
Causes:
 Bent or Worn out Sinkers
 Sinkers being tight in the Sinker Ring grooves
Remedies:
 Replace all the worn out or bent sinkers causing Sinker lines in the fabric.
 Sinker lines are very fine & feeble vertical lines appearing in the fabric.
 Remove the fibers clogging the Sinker tricks (Groove)

Fabric Press Off
Fabric press off appears, as a big or small hole in the fabric, caused due to the
interruption of the, loop forming process, as a result of the yarn breakage, or closed
needle hooks.
Causes:
 End breakage on feeders, with all needles knitting.
 Yarn feeder remaining in lifted up position, due to which, the yarn doesn’t get fed in the
hooks of the needles.
Remedies:
 Needle detectors, should be set precisely, to detect the closed needles & prevent the
fabric tube from completely pressing off.
 Proper yarn tension should be maintained, on all the feeders.

Needle lines
Needle lines are prominent, vertical lines, along the length of the fabric, which are
easily visible in the grey as well as finished fabric.
Causes:
 Bent Latches, Needle Hooks & Needle stems
 Wrong Needle selection (Wrong sequence of needles, put in the Cylinder or Dial)
Remedies:
 Inspect the grey fabric on the knitting machine for any Needle lines.
 Check the Needle filling sequence in the Cylinder / Dial grooves (tricks).

Pin Hole
Causes:
 Due to break down or bend of the latch, pin hole may come in the fabric.
 Improper tension.
 Same drive for both knit & tucks stitch.
 Curved needle latch.
Remedies:
 Different drive has to maintain
 Needle has to change.

Oil stain
When oil lick through the needle trick then it pass on the fabrics and make a line. It
is called oil stain/line.
Causes:
 Grease & Oil stains from the unguarded moving machine parts
 Fabric touching the floors & other soiled places, during transportation, in the trolleys
Remedies:
 Needle detectors, should be set precisely, to detect the closed needles & prevent the
fabric tube from completely pressing off.
 Proper yarn tension should be maintained, on all the feeders.

Lycra Out
Causes:
 Fail to catch the Lycra yarn by needle.
 Low tension of Lycra yarn.
 Lycra yarn breakage.
 Faulty auto stop motion
Remedies:
 Ensure the feed of Lycra yarn to every needle.
 The tension of Lycra yarn should be uniform.
 Auto stop motion should work properly.

Slub:
Causes:
 Usually caused by a thick or heavy place in yarn or by ling getting onto yarn
feeds.
Remedy:
 By using Good quality yarn

Measurement Problems
The measurements of the garments totally change after, a few hours of relaxation
& after the first wash. The arm lengths or the front & back lengths of the garments
may vary, due to the mix up of the parts.
Causes:
 Shrinkage caused due to the inadequate relaxation of the knitted fabrics, before cutting.
 Mixing of the garment parts cut from, different layers or different rolls of the knitted
fabric.
Remedies:
 Use a trolley, for laying the fabric on the table, to facilitate a tension free, laying.
 Let the fabric relax for a few hours, before cutting, especially the Lycra fabrics.
 Ensure the numbering of the different layers of the fabric, to prevent the mix up of the
components.
Conclusion
Detection of faults during production of knitted fabric is crucial for improved quality and
productivity.
This presentation will present and discuss the detection of faults and malfunctions during the
production remedies of knitted fabric.
We believe that our work will help the knitters to identify the source of detected faults &
proposes specific solutions for theses faults causes. So Knitters can take necessary remedial steps
to overcome the faults.
______________THE END_____________

Faults in the Knitted Fabrics

Recommended

Recommended

More Related Content

What's hot

What's hot (20)

Similar to Faults in the Knitted Fabrics

Similar to Faults in the Knitted Fabrics (20)

More from জুবায়ের আহমেদ ত্বহা

More from জুবায়ের আহমেদ ত্বহা (6)

Recently uploaded

Recently uploaded (20)

Faults in the Knitted Fabrics