Trusses Sections

TRUSSES–THE METHOD OF SECTIONS (Section 6.4) Today’s Objectives : Students will be able to determine forces in truss members using the method of sections. ,[object Object],[object Object],[object Object],[object Object],[object Object],[object Object],[object Object],[object Object]

READING QUIZ 1. In the method of sections, generally a “cut” passes through no more than _____ members in which the forces are unknown. A) 1 B) 2 C) 3 D) 4 2. If a simple truss member carries a tensile force of T along its length, then the internal force in the member is ______ . A) tensile with magnitude of T/2 B) compressive with magnitude of T/2 C) compressive with magnitude of T D) tensile with magnitude of T

APPLICATIONS Long trusses are often used to construct bridges. The method of joints requires that many joints be analyzed before we can determine the forces in the middle part of the truss. Is there another method to determine these forces directly?

THE METHOD OF SECTIONS In the method of sections, a truss is divided into two parts by taking an imaginary “cut” (shown here as a-a) through the truss. Since truss members are subjected to only tensile or compressive forces along their length, the internal forces at the cut member will also be either tensile or compressive with the same magnitude. This result is based on the equilibrium principle and Newton’s third law .

STEPS FOR ANALYSIS 1. Decide how you need to “cut” the truss. This is based on: a) where you need to determine forces, and, b) where the total number of unknowns does not exceed three (in general). 2. Decide which side of the cut truss will be easier to work with (minimize the number of reactions you have to find). 3. If required , determine the necessary support reactions by drawing the FBD of the entire truss and applying the EofE.

PROCEDURE (continued) 4. Draw the FBD of the selected part of the cut truss. We need to indicate the unknown forces at the cut members. Initially we assume all the members are in tension, as we did when using the method of joints. Upon solving, if the answer is positive, the member is in tension as per our assumption. If the answer is negative, the member must be in compression. (Please note that you can also assume forces to be either tension or compression by inspection as was done in the figures above.)

PROCEDURE (continued) 5. Apply the equations of equilibrium (EofE) to the selected cut section of the truss to solve for the unknown member forces. Please note that in most cases it is possible to write one equation to solve for one unknown directly.

EXAMPLE Given : Loads as shown on the roof truss. Find : The force in members DE, DL, and ML. Plan: a) Take a cut through the members DE, DL, and ML. b) Work with the left part of the cut section. Why? c) Determine the support reaction at A. What are they? d) Apply the EofE to find the forces in DE, DL, and ML.

EXAMPLE (continued) Analyzing the entire truss, we get  F X = A X = 0. By symmetry, the vertical support reactions are A Y = I Y = 36 kN + M D = – 36 (8) + 6 (8) + 12 (4) + F ML (5) = 0 F ML = 38 . 4 kN ( T )

EXAMPLE (continued) ,[object Object],+  M L = – 36 (12) + 6 (12) + 12 (8) + 12 (4) – F DE ( 4/  17)(6) = 0 F DE = – 37 . 11 kN or 37.1 kN (C)

CONCEPT QUIZ 1. Can you determine the force in member ED by making the cut at section a-a? Explain your answer. A) No, there are 4 unknowns. B) Yes, using  M D = 0 . C) Yes, using  M E = 0 . D) Yes, using  M B = 0 .

CONCEPT QUIZ 2. If you know F ED , how will you determine F EB ? A) By taking section b-b and using  M E = 0 B) By taking section b-b, and using  F X = 0 and  F Y = 0 C) By taking section a-a and using  M B = 0 D) By taking section a-a and using  M D = 0

GROUP PROBLEM SOLVING Given : Loading on the truss as shown. Find : The force in members BC, BE, and EF. Plan: a) Take a cut through the members BC, BE, and EF. b) Analyze the top section (no support reactions!). c) Draw the FBD of the top section. d) Apply the equations of equilibrium such that every equation yields answer to one unknown.

SOLUTION +   F X = 5 + 10 – F BE cos 45 º = 0 F BE = 21 . 2 kN (T) +  M E = – 5(4) + F CB (4) = 0 F CB = 5 kN (T) +  M B = – 5 (8) – 10 (4) – 5 (4) – F EF (4) = 0 F EF = – 25 kN or 25 kN (C)

ATTENTION QUIZ 1. As shown, a cut is made through members GH, BG and BC to determine the forces in them. Which section will you choose for analysis and why? A) Right, fewer calculations. B) Left, fewer calculations. C) Either right or left, same amount of work. D) None of the above, too many unknowns.

ATTENTION QUIZ 2. When determining the force in member HG in the previous question, which one equation of equilibrium is best to use? A)  M H = 0 B)  M G = 0 C)  M B = 0 D)  M C = 0

End of the Lecture Let Learning Continue

Trusses Sections

Recommended

Recommended

More Related Content

What's hot

What's hot (20)

Viewers also liked

Viewers also liked (20)

Similar to Trusses Sections

Similar to Trusses Sections (20)

More from Amr Hamed

More from Amr Hamed (15)

Trusses Sections

Editor's Notes